Toshiba Estia RUA-CP1701H Скачать руководство пользователя страница 63

Страница: 63 / 94

Monobloc Outdoor Unit Installation Manual

10.0 Control overview

10.1 Operating modes

Occupancy mode:

Depending on unit configuration, the system can be controlled in two ways. The first possible method embraces

the use of setpoints, where the outdoor air temperature has no effect on the temperature set by the control. The

second control method is based on a climatic curve. In this case, the water temperature is adjusted in response to

changes in the external temperature.

The unit may operate in HOME, SLEEP, or AWAY mode. The occupancy can be set manually by the user or

automatically according to the schedule (refer to remote controller end user manual).

Occupancy

RC Display

Comfort Type

Home

Comfort

Sleep

Comfort

Away

Eco

CAUTION: In case of power cycle, the previous operating mode (cooling / heating / DHW) or occupancy

mode (home / sleep / away) will be automatically restored.

10.2 Operating modes:

The user can normally choose one of three available operating modes, i.e. cooling, heating or domestic hot water

production only. Other modes such as booster cooling or booster heating, purge, and drying, can be selected only

with service access level.

The unit may run in the following modes:

• Off: Unit is requested to stop.

• Cool: Unit is requested to run in Cooling mode.

• Heat: Unit is requested to run in Heating mode.

• DHW Only: Unit is requested to run in DHW mode Only.

• Booster Cool: Unit is requested to run in Cooling mode at maximum compressor frequency.

• Booster Heat: Unit is requested to run in Heating mode at maximum compressor frequency.

• Purge: Water pump is requested to run in order to purge the hydraulic circuit.

• Drying: Unit is requested to run in Heating mode and the heating water setpoint is increased in order to dry

UFH.

System Mode

RC Display

Icon

Off

[no icon]

Cool

[steady icon]

Heat

[steady icon]

DHW only

[steady icon]

Booster Cool*

[flashing fast]

Booster Heat*

[flashing fast]

Purge*

[flashing fast]

Drying*

[flashing slow]

*Service access level only (with password 0120)

For more information on user interface, please refer to the WUI end user manual.

Содержание Estia RUA-CP1701H































































































Результаты поиска

Содержание Estia RUA-CP1701H

Отзывы:

Похожие инструкции для Estia RUA-CP1701H

Бренды по названию

Популярные бренды

Toshiba Estia RUA-CP1701H, Руководство по установке

Результаты поиска

Содержание Estia RUA-CP1701H

Отзывы:

Похожие инструкции для Estia RUA-CP1701H

Бренды по названию

Популярные бренды