Toshiba e-studio 2555c Скачать руководство пользователя страница 102 | Manualshive

Страница: 102 / 136

background image

6 TROUBLESHOOTING FOR NETWORK CONNECTIONS

100 Printing Problems (Network Related)

Printing Problems (Network Related)

Among the several ways to use the equipment in the network, the simplest one is to set the equipment in the
TCP/IP environment using a DHCP server to assign IP addresses dynamically to devices. Using the default
settings also assures an easier network implementation, although you may be required to customize the
settings to accommodate them in your particular environment.

Some common network configurations are shown below, along with the steps required to configure the
equipment. If you perform all the steps in the applicable checklist and still cannot print satisfactorily with the
equipment, contact your service representative.

y

You can change the network protocol settings with the touch panel of the equipment or with TopAccess
(the Administration page).

y

For the error messages that appear during the installation of the printer drivers, refer to the

Software

Installation Guide

.

SMB print in a Windows operating system environment

No Check...

Yes

No

Corrective Action

1

Are the IP address properties correctly
set?

Next

Step

Ø

Ö

Set up the IP address correctly.

2

Is the Microsoft computer name (device
name) unique?

Next

Step

Ø

Ö

Set up the device name correctly.

3

Is the workgroup name valid and
correctly entered?

Next

Step

Ø

Ö

Set up the workgroup correctly.

4

When IPv4 is supported: Is the WINS
server address correctly set?
When IPv6 is supported: Is LLMNR for
the IPv6 setting enabled?

Next

Step

Ø

Ö

When IPv4 is supported: Set up the
WINS server address correctly, or enter
“0.0.0.0” for the WINS server address to
disable the WINS service.
When IPv6 is supported: Enable
LLMNR for the IPv6 setting referring to
the

TopAccess Guide

.

5

When IPv4 is supported: If the client
computers are located in different
segments, is the WINS service correctly
provided?

Next

Step

Ø

Ö

When IPv4 is supported: Set up the
WINS server and enable it on the
equipment to allow users access from a
different segment.

6

Can you see the equipment in Windows
Network Neighborhood?

Next

Step

Ø

Ö

See the following section to fix the
problem:

P.94 “Cannot locate the equipment

in the network”

7

Were the proper printer drivers
installed?

Next

Step

Ø

Ö

Refer to the

Software Installation

Guide

to install the proper printer

drivers.

8

Is the driver’s port name valid?

Next

Step

Ø

Ö

Refer to the

Software Installation

Guide

to configure the proper port.

9

Can you print with the equipment?

End

Ö

See the following section to fix the
problem:

P.82 “Cannot print with the

equipment (network connection
problems)”

«
...
100
101
102
103
104
...
»

Содержание e-studio 2555c









































































































































Отзывы:

Нет отзывов

Похожие инструкции для e-studio 2555c

Бренд: EBS Страницы: 4

Бренд: NCR Страницы: 38

Бренд: Lexmark Страницы: 8

Бренд: Oki Страницы: 4

Бренд: Olivetti Страницы: 22

Бренд: Konica Minolta Страницы: 44

Бренд: Oki Страницы: 8

Бренд: Star Micronics Страницы: 194

Бренд: Microcom Страницы: 207

Бренд: Canon Страницы: 327

Бренд: Savin Страницы: 90

Бренд: Muratec Страницы: 6

Pacemark PM4410

Бренд: Oki Страницы: 28

imageprograf IPF785

Бренд: Canon Страницы: 640

Бренд: MIMAKI Страницы: 12

Бренд: Canon Страницы: 120

Bubble Jet Pixma iX4000

Бренд: Canon Страницы: 10

Cassette Module-Y1

Бренд: Canon Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды