Toshiba e-studio 2555c Скачать руководство пользователя страница 121 | Manualshive

Страница: 121 / 136

background image

7.CHECKING THE EQUIPMENT STATUS WITH TopAccess

Error Codes 119

7 CHECKING THE EQUIPMENT STATUS WITH TopAccess

2D40

Failure to convert image file format

This error occurs when conversion to a
highly compressed PDF format fails. Do the
scanning again. If the error still persists, Use
the normal PDF format. When this error
occurs in conversion other than to a highly
compressed PDF format, turn the power
OFF and then back ON. Then try to scan
again. If the error still persists, contact your
service representative.

2D43

Encryption error. Failure to create a file

If the error still persists after reattempting,
turn the power OFF and then back ON. Then
make another effort.

2D44

Creating a file was not allowed.

Creating an unencrypted file was not
allowed. Configure the encryption settings
and try again. To create an unencrypted file,
consult the administrator.

2D45

Failure in making meta data

Make sure that the template setting is
correct, and do the scanning again. If the
error still persists, turn the power OFF and
then back ON, and then try again.

2D62

Failure to connect to network destination
Check destination path.

Make sure that the network folder is shared
in your network and try scanning again. If
the error still persists, ask your administrator
to check whether the IP address or path of
the server is correct. Also make sure that the
server is operating properly.

2D63

Specified network path is invalid. Check
destination path.

Make sure that you specify the correct
network folder and try scanning again.

2D64

Log on to file server failed. Check user name
and password.

Make sure that you specify the correct user
name and password to log on the file server,
or you specify the correct file server. Then
try scanning again.

2D65

There are too many documents in the folder.
Failure in creating a new document

Delete the data in the local storage folder in
the equipment and try scanning again.

2D66

Failed to process your job. Insufficient
Storage space.

Reduce the number of pages of the problem
job and try again. Check whether the server
or local disk has sufficient space in its
capacity.

2D67

FTP service is not available

Ask your administrator whether the FTP
service is configured correctly.

2D68

File Sharing service is not available

Ask your administrator whether the SMB
protocol is enabled.

2D69

NetWare service is not available

Ask your administrator whether the NetWare
protocol is enabled.

2DA6

Failure to delete file

Delete the files in the shared folder with
Explorer, turn the power OFF and then back
ON, and reattempt the problem job. If the
error still persists, contact your service
representative.

2DA7

Failure to acquire resource

Turn the power OFF and then back ON. Try
the problem job again. If the error still
persists, contact your service representative.

2DC0

Job canceled

The job was canceled.

Error Code

Problem Description

Corrective Action

«
...
119
120
121
122
123
...
»

Содержание e-studio 2555c









































































































































Отзывы:

Нет отзывов

Похожие инструкции для e-studio 2555c

Бренд: TallyGenicom Страницы: 145

T2265 SprintPro

Бренд: Tally Страницы: 217

Бренд: TallyGenicom Страницы: 12

Бренд: Xerox Страницы: 3

Бренд: Xerox Страницы: 8

Versant 3100 Press

Бренд: Xerox Страницы: 45

Бренд: Canon Страницы: 36

Бренд: Canon Страницы: 62

WorkCentre 4260S

Бренд: Xerox Страницы: 8

Бренд: Canon Страницы: 738

Бренд: Samsung Страницы: 143

imageRUNNER 6570

Бренд: Canon Страницы: 274

Бренд: Xerox Страницы: 14

Бренд: Xerox Страницы: 2

Aficio SP C420DN

Бренд: Ricoh Страницы: 4

Бренд: SEWOO Страницы: 17

Бренд: Oce Страницы: 209

Бренд: OmniPrint Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды