Toshiba e-studio 2555c Скачать руководство пользователя страница 113 | Manualshive

Страница: 113 / 136

background image

7 CHECKING THE EQUIPMENT STATUS WITH TopAccess

Error Messages 111

Paper Misfeed in Automatic Duplexing Unit - Please
Clear Paper Path.

Refer to the guidance on the touch panel to remove
misfed paper.

Paper Insertion Misfeed - Please Clear Paper Path.

Refer to the guidance on the touch panel to remove
misfed paper.

Paper Misfeed in Printer - Please Clear Paper Path.

Refer to the guidance on the touch panel to remove
misfed paper.

Paper Misfeed in Finisher - Please Clear Paper
Path.

Remove the misfed paper from the Finisher.
See

P.15 “Clearing a Paper Misfeed”.

Used Toner Container Full - Please Replace.

Replace the waste toner box.
See

P.59 “Replacing the Waste Toner Box”.

Staple Empty - Please Set Staple Cartridge

Refill the Finisher staples.
See

P.61 “Refilling finisher staples”.

Open the front cover, and clean the slit glass and
main charger.

Clean the slit glass and the main chargers.

Toner Not Recognized - Please Check Toner.

Check and adjust the toner bottle.

Black Toner Empty - Please Install New Toner
Cartridge.

Replace the black toner.
See

P.52 “Replacing a Toner Cartridge”.

Cyan Toner Empty - Please Install New Toner
Cartridge.

Replace the cyan toner.
See

P.52 “Replacing a Toner Cartridge”.

Magenta Toner Empty - Please Install New Toner
Cartridge.

Replace the magenta toner.
See

P.52 “Replacing a Toner Cartridge”.

Yellow Toner Empty - Please Install New Toner
Cartridge.

Replace the yellow toner.
See

P.52 “Replacing a Toner Cartridge”.

Black Toner Near Empty - Please Prepare New
Toner Cartridge.

Prepare the new toner cartridge.

Cyan Toner Near Empty - Please Prepare New
Toner Cartridge.

Prepare the new toner cartridge.

Magenta Toner Near Empty - Please Prepare New
Toner Cartridge.

Prepare the new toner cartridge.

Yellow Toner Near Empty - Please Prepare New
Toner Cartridge.

Prepare the new toner cartridge.

Confirm waste toner bottle is attached and close
waste toner bottle cover.

Confirm the waste toner box is securely attached
and close the waste toner box cover.

Close duplexing unit cover

Close the duplexing unit cover.

Close receiving tray low cover

Close the low cover of the receiving tray.

Prepare new waste toner box

Prepare a new waste toner box.

Fatal Error - Please Contact Service Technician.

Contact your service representative.

Main Motor Error - Please Contact Service
Technician.

Contact your service representative.

Printer Input Error.

Contact your service representative.

Scanner Error - Please Contact Service Technician.

Contact your service representative.

Fuser Error - Please Contact Service Technician.

Contact your service representative.

TopAccess Message

Corrective Action

«
...
111
112
113
114
115
...
»

Содержание e-studio 2555c









































































































































Отзывы:

Нет отзывов

Похожие инструкции для e-studio 2555c

Sure shot 80 tele

Бренд: Canon Страницы: 24

iPF720 - imagePROGRAF Color Inkjet Printer

Бренд: Canon Страницы: 8

Бренд: Canon Страницы: 2

Perfecta 3600STP

Бренд: Variquest Страницы: 12

Perfecta 3600STP

Бренд: Variquest Страницы: 231

Awards Maker 400

Бренд: Variquest Страницы: 4

Бренд: OKIDATA Страницы: 13

Бренд: Canon Страницы: 4

Бренд: BIXOLON Страницы: 59

Бренд: Printek Страницы: 34

Бренд: Oki Страницы: 336

8200DX - Phaser Color Solid Ink Printer

Бренд: Xerox Страницы: 2

ECOSYS FS-6530MFP

Бренд: Kyocera Страницы: 2

DocumentCentre C240 Series

Бренд: Fuji Xerox Страницы: 275

Бренд: Lexmark Страницы: 10

Бренд: MHM Страницы: 52

Бренд: Lexmark Страницы: 60

Бренд: Ricoh Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды