Toshiba e-studio 2555c Скачать руководство пользователя страница 119 | Manualshive

Страница: 119 / 136

background image

7.CHECKING THE EQUIPMENT STATUS WITH TopAccess

Error Codes 117

7 CHECKING THE EQUIPMENT STATUS WITH TopAccess

2C15

Mail size exceeded limit or maximum size

You are sending too many documents at a
time. Send them separately.

2C30-2C33

Disk access error

Complete any running jobs first before
reperforming the job in error. If the error still
persists, turn the power OFF and then back
ON, and then try again.

2C40

Failed to convert image file format

This error occurs when conversion to a
highly compressed PDF format fails. Do the
scanning again. If the error still persists, Use
the normal PDF format. When this error
occurs in conversion other than to a highly
compressed PDF format, turn the power
OFF and then back ON. Then try to scan
again. If the error still persists, contact your
service representative.

2C43

Encryption error. Failure to create a file

If the error still persists after reattempting,
turn the power OFF and then back ON. Then
make another effort.

2C44

Creating a file was not allowed

Creating an unencrypted file was not
allowed. Configure the encryption settings
and try again. To create an unencrypted file,
consult the administrator.

2C45

Failure in making meta data

Make sure that the template setting is
correct, and do the scanning again. If the
error still persists, turn the power OFF and
then back ON, and then try again.

2C60

HDD full failure during processing

Reduce the number of pages of the problem
job and try again. Check whether the server
or local disk has sufficient space in its
capacity.

2C61

Failure to read Address Book

Turn the power OFF and then back ON. Try
the problem job again. Reset the data in the
Address Book and reattempt it. If the error
still persists, contact your service
representative.

2C63

Terminal IP address unset

Ask your administrator to set the IP address
of the equipment.

2C64

Terminal mail address unset

Ask your administrator to set the Email
address of the equipment.

2C65, 2C66,

2C69

Failure to connect to SMTP server

Make sure that the SMTP server is correctly
working or the SMTP server address has
been set correctly.

2C6A

Failure to send Email message

Turn the power OFF and then back ON. Try
scanning again. If the error still persists,
contact your service representative.

2C6B

Invalid address specified in From: field

Ask your administrator to check the SMTP
Authentication method or if there is an
unpermitted character in the Terminal mail
address. Set the correct SMTP
Authentication method or delete the
unpermitted character in the Terminal mail
address.

Error Code

Problem Description

Corrective Action

«
...
117
118
119
120
121
...
»

Содержание e-studio 2555c









































































































































Отзывы:

Нет отзывов

Похожие инструкции для e-studio 2555c

Бренд: Xerox Страницы: 192

Бренд: Oki Страницы: 40

Бренд: Partner Страницы: 9

Бренд: Oki Страницы: 95

Donation Point Even

Бренд: Quest Payment Systems Страницы: 2

Бренд: Muratec Страницы: 6

Бренд: Velleman Страницы: 44

Бренд: Konica Minolta Страницы: 12

EuroLine Series

Бренд: Output Technology Страницы: 73

Бренд: SII Страницы: 85

Бренд: MIMAKI Страницы: 28

LaserPro X500 III-80Y

Бренд: GCC Technologies Страницы: 127

Бренд: Xerox Страницы: 18

Бренд: Wasp Страницы: 2

Бренд: Oki Страницы: 181

Бренд: Oki Страницы: 52

Бренд: Fujitsu Страницы: 126

Бренд: Fujitsu Страницы: 123

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды