Toshiba e-studio 2555c Скачать руководство пользователя страница 82 | Manualshive

Страница: 82 / 136

background image

3 TROUBLESHOOTING FOR PRINTING

80 Printer Driver Problems

Printer Driver Problems

This section describes the troubleshooting for the printer drivers.

For the error messages that appear during the installation of the printer drivers, refer to the

Software

Installation Guide

.

Cannot print (port setting problems)

Problem Description

I cannot perform printing with the equipment.

Corrective Action

If the printer driver on the client computer points to a wrong network port, jobs neither appear in the current
jobs queue nor are printed. Fix the problem following the procedure below:
1. Open the Printers folder from the Control Panel.
2. Right-click the printer driver icon.
3. Select Properties from the shortcut menu.
4. Select the [Ports] tab.
5. Make sure that the path to the printer and the device name are correct.

\\<device name>\print
<device name> is the same as the device name set from the touch panel. “print” may be “univ” or “ps3”
depending on the printer driver you use.

6. Click the [General] Tab and click [Print Test Page] to confirm that the settings are correct.

Cannot print (SNMP Community Name problems)

Problem Description

I cannot perform printing with the equipment.

Corrective Action

Check if the SNMP community names are the same in the following 3 settings.

y

Equipment

y

TCP/IP port of the [Ports] tab in the printer driver

y

[SNMP Settings] dialog box of the [Others] tab in the printer driver

Command line options not processed

Problem Description

All the print options are sent to the equipment at the beginning of the print job. If the print file already contains
print commands, they overwrite the command line options you set. For example, if the print file specifies Letter
paper, and you specify A4 paper with the lp command, the document is printed on Letter size paper.

Corrective Action

Change the properties of the document you intend to print to create another print file. Submit the print job
using the lp command without setting additional parameters.

«
...
80
81
82
83
84
...
»

Содержание e-studio 2555c









































































































































Отзывы:

Нет отзывов

Похожие инструкции для e-studio 2555c

Бренд: Unitech Страницы: 18

Бренд: Unitech Страницы: 26

Бренд: Panduit Страницы: 6

870 - SuperScript B/W Laser Printer

Бренд: NEC Страницы: 52

SuperScript 1800

Бренд: NEC Страницы: 8

Бренд: Unimark Страницы: 38

Бренд: Keeler Страницы: 25

Бренд: Konica Minolta Страницы: 44

Бренд: EFI Страницы: 4

ColorPainter M-64S

Бренд: Oki Страницы: 84

Бренд: Ricoh Страницы: 44

Bravo se Disc Publisher

Бренд: Primera Страницы: 58

Бренд: Xerox Страницы: 240

Digital Minilab Frontier LP5700R

Бренд: FujiFilm Страницы: 2

Бренд: Kyocera Страницы: 16

Бренд: Xerox Страницы: 78

Бренд: Infinite Peripherals Страницы: 27

MPK 1230XX Series

Бренд: NFCP Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды