Toshiba e-studio 2555c Скачать руководство пользователя страница 115

Страница: 115 / 136

7.CHECKING THE EQUIPMENT STATUS WITH TopAccess

Error Codes 113

7 CHECKING THE EQUIPMENT STATUS WITH TopAccess

Error codes on transmission and reception

4312

Not authorized to store a file

The user has not been authorized to perform this
operation. Ask your administrator.

4313

Not authorized to store in e-Filing

The user has not been authorized to perform this
operation. Ask your administrator.

4314

Not authorized to send a Fax/iFax The user has not been authorized to perform this

operation. Ask your administrator.

4321

Not authorized to perform printing
in the specified setting

The user has not been authorized to perform this
operation. Ask your administrator.

4411

Image data generation failure

Check if the file to be printed is broken. Perform printing
again or use another printer driver.

4412

Double-sign encoding error

A double-sign encoding error occurred because the PDF
file is encrypted in unsupported script. Printing the file in
this function is impossible.

4611

Font download failure

Since the available number of fonts is exceeded, the font
cannot be registered. Delete at least one font.

4612

Font download failure

Since there is no space in HDD, the font cannot be
registered. Delete at least one font.

4613

Font download failure

Since an error has occurred, the font cannot be registered.
Perform downloading again or regenerate the font data
first.

4621

Downloaded font deletion failure

Check if the font to be deleted is registered.

4F10

Print failure

If the error still persists after reattempting, turn the power
OFF and then back ON. Then make another effort. If the
error still persists, contact your service representative.

Error

Code

Problem Description

Corrective Action

Error

Code

Problem Description

Corrective Action

0012

Original misfeed

Remove the misfed original.

0013

Door open

Firmly close the open door.

0020

Power interruption

Check the power interruption report.

0030

Interruption by paper misfeeds
during direct transmission

Remove the misfed paper and reattempt the transmission.

0033

Polling Error

Check polling options setup (Security Code, etc.), and
check whether the polling document exists.

0042

Memory full

Make sure that there is sufficient memory before making
the call again.

0050

Line busy

Reattempt the communications.

0051

Fax line cable disconnected

Check if the fax line cable is connected. To clear the
message, press the [FUNCTION CLEAR] button twice.

0053

Security Mismatch in Relay or
Mail Box transmission

Confirm the remote party’s Security Code, system
password and your setup.

00B0-

00B5

00C0-

00C4

00D0-

00D2

Signal Error or Line Condition
Error

Reattempt the communications.

Содержание e-studio 2555c








































































































































Результаты поиска

Содержание e-studio 2555c

Отзывы:

Похожие инструкции для e-studio 2555c

Бренды по названию

Популярные бренды

Toshiba e-studio 2555c, Руководство по устранению неисправностей

Результаты поиска

Содержание e-studio 2555c

Отзывы:

Похожие инструкции для e-studio 2555c

Бренды по названию

Популярные бренды