Toshiba e-studio 2555c Скачать руководство пользователя страница 131 | Manualshive

Страница: 131 / 136

background image

8 WHEN SOMETHING IS WRONG WITH THE EQUIPMENT

Regular Maintenance 129

Regular Maintenance

We recommend that you clean the following portions weekly so that the originals can always be scanned in
unsoiled conditions.

y

Be careful not to scratch the portions when cleaning them.

y

When cleaning the surface of the equipment, do not use such organic solvents as thinner or benzine.

- This could warp the shape of the surface or leave it discolored.
- When using a chemical cleaning pad to clean it, follow the instructions.

1. Scanning area (surface of the long rectangular glass) / 2. Original glass

Wipe it with a soft dry cloth. If there are still stains remaining, clean with a piece of soft cloth which has
been moistened with water and then squeezed well. Do not use liquids other than water (such as alcohol,
organic solvents or neutral detergent).

3. Guide / 4. Platen sheet

Clean the surface as follows depending on the extent of the staining.

y

Clean it with a soft cloth.

y

Clean it with a soft cloth lightly moistened with water.

y

Clean it with a soft cloth lightly moistened with alcohol, and then wipe with a dry cloth.

y

Clean it with a soft cloth lightly moistened with watered-down neutral detergent, wipe with a cloth
moistened with water, and then wipe with a dry cloth.

1

2

3

4

«
...
129
130
131
132
133
...
»

Содержание e-studio 2555c









































































































































Отзывы:

Нет отзывов

Похожие инструкции для e-studio 2555c

Magicolor 2 Desklaser

Бренд: QMS Страницы: 60

Бренд: UltraTape Страницы: 52

SCX 4500W - Personal Wireless Laser Multi-Function...

Бренд: Samsung Страницы: 113

imageRUNNER ADVANCE 8105

Бренд: Canon Страницы: 5

imageCLASS MF269dw

Бренд: Canon Страницы: 32

Бренд: Samsung Страницы: 158

Бренд: Canon Страницы: 21

imageRUNNER ADVANCE 4251

Бренд: Canon Страницы: 12

Бренд: Seiko Страницы: 76

Бренд: Duplo Страницы: 123

Бренд: Oki Страницы: 40

SuperScript 610

Бренд: NEC Страницы: 105

Бренд: Colorjet Страницы: 52

AficioSP C410DN

Бренд: Ricoh Страницы: 204

Бренд: M&R Страницы: 36

Бренд: Xerox Страницы: 2

Бренд: Galileo Страницы: 15

Бренд: Lexmark Страницы: 221

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды