Toshiba e-studio 2555c Скачать руководство пользователя страница 122 | Manualshive

Страница: 122 / 136

background image

7 CHECKING THE EQUIPMENT STATUS WITH TopAccess

120 Error Codes

2DC1

Power failure occurred

Make sure that the power cable is
connected properly and is inserted securely.
Resend the job.

Store to USB

2E10, 2E12,

2E13

Wrong Job status

Turn the power OFF and then back ON. Try
the problem job again. If the error still
persists, contact your service representative.

2E11

Not enough memory

Wait for a while and try again. If the error still
persists, turn the power OFF and then back
ON, and make another effort.

2E14

Invalid parameter specified

If you are using a template, create it again. If
the error still persists, turn the power OFF
and then back ON, and then try again.

2E15

Document size exceeded limit or maximum
size

Divide the file into several files, or reattempt
in a single-page format.

2E30

Failure to create directory

Make sure that the access privilege to the
storage directory is writable and also that the
disk in the directory has enough space, and
then try again. If more than one job is
performed simultaneously, the error may
occur because the disk temporarily runs out
of space. In this case, wait for a while and try
again. If the error still persists, turn the
power OFF and then back ON, and make
another effort.

2E31, 2E33

Failure to create file

Make sure that the access privilege to the
storage directory is writable and also that the
disk in the directory has enough space, and
then try again. If more than one job is
performed simultaneously, the error may
occur because the disk temporarily runs out
of space. In this case, wait for a while and try
again. If the error still persists, turn the
power OFF and then back ON, and make
another effort.

2E32

Failure to delete file

Turn the power OFF and then back ON. Try
the problem job again. If the error still
persists, contact your service representative.

2E40

Failure to convert image file format

This error occurs when conversion to a
highly compressed PDF format fails. Do the
scanning again. If the error still persists, Use
the normal PDF format. When this error
occurs in conversion other than to a highly
compressed PDF format, turn the power
OFF and then back ON. Then try to scan
again. If the error still persists, contact your
service representative.

2E43

Encryption error Failure to create a file

If the error still persists after reattempting,
turn the power OFF and then back ON. Then
make another effort.

2E44

Creating a file was not allowed

Creating an unencrypted file was not
allowed. Configure the encryption settings
and try again. To create an unencrypted file,
consult the administrator.

Error Code

Problem Description

Corrective Action

«
...
120
121
122
123
124
...
»

Содержание e-studio 2555c









































































































































Отзывы:

Нет отзывов

Похожие инструкции для e-studio 2555c

KXPX2M - HOME PHOTO PRINTER

Бренд: Panasonic Страницы: 28

Бренд: Panasonic Страницы: 78

Бренд: Panasonic Страницы: 4

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 9

Jetwriter KX-CL500

Бренд: Panasonic Страницы: 32

Бренд: Samsung Страницы: 165

Бренд: Samsung Страницы: 2

Inkjet SCX-1150F

Бренд: Samsung Страницы: 66

Бренд: Samsung Страницы: 155

CLX-3170FN series

Бренд: Samsung Страницы: 220

CLX 6210FX - Color Laser - All-in-One

Бренд: Samsung Страницы: 36

CLX-3160 Series

Бренд: Samsung Страницы: 139

Бренд: Samsung Страницы: 8

Lazett Combo SCX-4016

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 319

DocuPrint C525 A

Бренд: Xerox Страницы: 49

DocuPrint C2100

Бренд: Xerox Страницы: 206

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды