manualshive.com logo in svg

Toro Z580-D Z Master 74266, Руководство оператора


Поделиться
Скачать
background image

This product complies with all relevant European
directives, for details please see the separate product
specific Declaration of Conformity (DOC) sheet.

Introduction

This rotary-blade, riding lawn mower is intended to
be used by residential homeowners or professional,
hired operators. It is designed primarily for cutting
grass on well-maintained lawns on residential
or commercial properties. It is not designed for
cutting brush or for agricultural uses.

Read this information carefully to learn how to operate
and maintain your product properly and to avoid injury
and product damage. You are responsible for operating
the product properly and safely.

You may contact Toro directly at www.Toro.com for
product and accessory information, help finding a
dealer, or to register your product.

Whenever you need service, genuine Toro parts, or
additional information, contact an Authorized Service
Dealer or Toro Customer Service and have the model
and serial numbers of your product ready. Figure 1
identifies the location of the model and serial numbers
on the product. Write the numbers in the space
provided.

Figure 1

1.

Model and serial number location

Model No.

Serial No.

This manual identifies potential hazards and has
safety messages identified by the safety alert symbol
(Figure 2), which signals a hazard that may cause serious

injury or death if you do not follow the recommended
precautions.

Figure 2

1.

Safety alert symbol

This manual uses 2 other words to highlight information.

Important

calls attention to special mechanical

information and

Note

emphasizes general information

worthy of special attention.

Contents

Introduction................................................................. 2
Safety ........................................................................... 4

Safe Operating Practices ....................................... 4
Toro Riding Mower Safety .................................... 5
Sound Pressure..................................................... 6
Sound Power ........................................................ 6
Vibration Level .................................................... 6
Slope Indicator..................................................... 7
Safety and Instructional Decals ............................. 8

Product Overview ...................................................... 15

Controls ............................................................. 15

Operation................................................................... 16

Adding Fuel ....................................................... 16
Biodiesel Ready .................................................. 17
Filling the Fuel Tank........................................... 17
Checking the Engine Oil Level............................ 17
Switching the Fuel Tanks .................................... 17
Using the Rollover Protection System

(ROPS) .......................................................... 18

Think Safety First ............................................... 19
Operating the Parking Brake ............................... 20
Starting and Stopping the Engine ........................ 20
Operating the Power Take Off (PTO) ................. 22
The Safety Interlock System................................ 22
Driving Forward or Backward............................. 23
Stopping the Machine......................................... 24
Adjusting the Height-of-Cut ............................... 24
Adjusting the Anti-Scalp Rollers ......................... 24
Adjusting the Flow Baffle ................................... 25
Positioning the Flow Baffle................................. 26
Using the Lift Assist Lever .................................. 26
Positioning the Seat ............................................ 27
Unlatching the Seat............................................. 27
Pushing the Machine by Hand............................. 27
Using the Side Discharge .................................... 28
Operating with the Overheat Sensor ................... 28

© 2010—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420

2

Contact us at www.Toro.com.

Printed in the USA.

All Rights Reserved

Содержание Z580-D Z Master 74266





































































Отзывы:

Нет отзывов

Похожие инструкции для Z580-D Z Master 74266

Yard-Man 107 Operator'S Manual preview
107
Бренд: Yard-Man Страницы: 16
Makita PLM4630N2 Instruction Manual preview
PLM4630N2
Бренд: Makita Страницы: 52
Walker MT, MTL, MTEFI, MTLEFI Detailed Instructions preview
MT, MTL, MTEFI, MTLEFI
Бренд: Walker Страницы: 256
Walker T23 Operator'S Manual preview
T23
Бренд: Walker Страницы: 96
Cub Cadet 18.5HP Z-Force 42 Illustrated Parts List preview
18.5HP Z-Force 42
Бренд: Cub Cadet Страницы: 56
Land Pride Z44 Accu-Z Razor Service Manual preview
Z44 Accu-Z Razor
Бренд: Land Pride Страницы: 72
Big League Lawns CheckMate 21462 Installation Manual preview
CheckMate 21462
Бренд: Big League Lawns Страницы: 4
Yard-Man 1070-9 Operating Manual And Parts List preview
1070-9
Бренд: Yard-Man Страницы: 12
Yard-Man 147W834H401 Series Owner'S Manual preview
147W834H401 Series
Бренд: Yard-Man Страницы: 40
Ego Power+ LM1900E Operator'S Manual preview
LM1900E
Бренд: Ego Power+ Страницы: 444
Bushranger 53AH6IMSP Operator'S Manual preview
53AH6IMSP
Бренд: Bushranger Страницы: 20
The Handy 193875002 Instruction Manual preview
193875002
Бренд: The Handy Страницы: 20
Yazoo SV24W-3 Parts Manual preview
SV24W-3
Бренд: Yazoo Страницы: 8
Gravely 408 Owner'S Manual preview
408
Бренд: Gravely Страницы: 8
Gardena EasyCut 400 Operating Instructions Manual preview
EasyCut 400
Бренд: Gardena Страницы: 14
Exmark LAZER Z AS Setup Instructions preview
LAZER Z AS
Бренд: Exmark Страницы: 5
EINHELL 34.132.26 Original Operating Instructions preview
34.132.26
Бренд: EINHELL Страницы: 189
EINHELL FREELEXO Original Operating Instructions preview
FREELEXO
Бренд: EINHELL Страницы: 94

Бренды по названию

Популярные бренды

Загрузить еще бренды