manualshive.com logo in svg

Toro Z580-D Z Master 74266, Руководство оператора, Страница: 43 / 68

Поделиться
Скачать
Toro Z580-D Z Master 74266 Скачать руководство пользователя страница 43

1

3

2

G012492

4

Figure 55

1.

Ignition-30 amp (F1)

3.

Clutch-10 amp (F3)

2.

Radiator fan-50 amp
(large, heavy duty fuse)

4.

Left side fuel tank

Drive System
Maintenance

Adjusting the Tracking

The machine has a knob for adjusting the tracking
located under the seat.

Important:

Adjust the handle neutral and

hydraulic pump neutral before adjusting the
tracking. Refer to Adjusting the Handle Neutral
in Controls System Maintenance (page 52)
and Adjusting the Hydraulic Pump Neutral
in Hydraulic System Maintenance (page 53).

1. Push both control levers forward the same distance.

2. Check if the machine pulls to one side. If it does,

stop the machine and set the parking brake.

3. Unlatch the seat and tilt the seat forward to access

the tracking knob.

Note:

Determine the left and right sides of the

machine from the normal operating position.

4. To make the machine go right, turn the knob towards

the rightside of the machine. Refer to Figure 56.

5. To make the machine go left, turn the knob towards

the leftside of the machine. Refer to Figure 56.

6. Repeat adjustment until the tracking is correct.

43

Содержание Z580-D Z Master 74266





































































Отзывы:

Нет отзывов