Toro Z580-D Z Master 74266 Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 68

background image

Electrical System
Maintenance

Servicing the Battery

WARNING

CALIFORNIA

Proposition 65 Warning

Battery posts, terminals, and related

accessories contain lead and lead compounds,

chemicals known to the State of California

to cause cancer and reproductive harm.

Wash hands after handling.

DANGER

Battery electrolyte contains sulfuric acid which is a
deadly poison and causes severe burns.

Do not drink electrolyte and avoid contact with
skin, eyes or clothing. Wear safety glasses to shield
your eyes and rubber gloves to protect your hands.

Removing the Battery

WARNING

Battery terminals or metal tools could short against
metal machine components causing sparks. Sparks
can cause the battery gasses to explode, resulting
in personal injury.

•

When removing or installing the battery, do not
allow the battery terminals to touch any metal
parts of the machine.

•

Do not allow metal tools to short between
the battery terminals and metal parts of the
machine.

WARNING

Incorrect battery cable routing could damage the
machine and cables causing sparks. Sparks can
cause the battery gasses to explode, resulting in
personal injury.

•

Always Disconnect the negative (black) battery
cable before disconnecting the positive (red)
cable.

•

Always Reconnect the positive (red) battery
cable before reconnecting the negative (black)
cable.

1. Disengage the PTO, move the motion control levers

to the neutral locked position and set the parking
brake.

2. Stop the engine, remove the key, and wait for all

moving parts to stop before leaving the operating
position.

3. Unlatch the seat and tilt the seat up.

4. First disconnect the negative battery cable from the

negative (-) battery terminal (Figure 52).

5. Slide the red terminal boot off the positive (red)

battery terminal. Then remove the positive (red)
battery cable (Figure 52).

Figure 52

1.

Negative Battery Post

3.

Red (+) cable

2.

Positive Battery Post

4.

Black (-) cable

6. Remove both wing nuts (1/4 inch) securing the

battery clamp (Figure 53).

7. Remove the two bolts holding the hydraulic tank in

place (Figure 53).

8. Slide the hydraulic tank away from the battery.

9. Remove the battery.

41

«
...
39
40
41
42
43
...
»

Содержание Z580-D Z Master 74266





































































Отзывы:

Нет отзывов

Похожие инструкции для Z580-D Z Master 74266

Бренд: Grizzly Страницы: 76

Бренд: Bad Boy Страницы: 32

Бренд: Tar River Страницы: 56

Бренд: Poulan Pro Страницы: 56

Бренд: Parker Страницы: 25

Бренд: Yard-Man Страницы: 4

Patriot FDR1660

Бренд: Land Pride Страницы: 2

Бренд: Yard force Страницы: 11

Бренд: Stiga Страницы: 296

Бренд: Snapper Страницы: 224

ULTRAVAC BAGGER

Бренд: Exmark Страницы: 19

Super Surfer II GSKA1948S

Бренд: Great Dane Страницы: 78

Бренд: Yard-Man Страницы: 8

Бренд: RHINO Страницы: 160

Бренд: Cub Cadet Страницы: 9

Бренд: Simplicity Страницы: 4

Бренд: Simplicity Страницы: 4

Бренд: Simplicity Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды