Toro Z580-D Z Master 74266 Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 68

Toro Z580-D Z Master 74266 Скачать руководство пользователя страница 40

Changing the Fuel Filter

Never install a dirty fuel filter if it is removed from the
fuel line.

1. Allow the machine to cool down.

2. Disengage the PTO, move the motion control levers

to the neutral locked position and set the parking
brake.

3. Stop the engine, remove the key, and wait for all

moving parts to stop before leaving the operating
position.

4. Close the fuel shut-off valve(Figure 51).

5. Loosen the two hose clamps and disconnect the fuel

lines from the fuel filter (Figure 51).

6. Install a new filter. Connect the fuel lines to the fuel

filter and install the two hose clamps (Figure 51).

7. Open the fuel shut-off valve.

8. Start the engine and check for leaks.

Figure 51

1.

Fuel filter

4.

Left side of machine

2.

Hose clamp

5.

Fuel shut-off valve

3.

Fuel pump

Servicing the Fuel Tank

Do not attempt to drain the fuel tank because fuel line
components require special tools to install them. Ensure
that an Authorized Service Dealer drains the fuel tank
and services any components of the fuel system.

40

«
...
38
39
40
41
42
...
»

Содержание Z580-D Z Master 74266





































































Отзывы:

Нет отзывов