manualshive.com logo in svg

Toro Z580-D Z Master 74266, Руководство оператора, Страница: 51 / 68

Поделиться
Скачать
Toro Z580-D Z Master 74266 Скачать руководство пользователя страница 51

Figure 71

1.

Clutch

3.

Spring

2.

Pump drive belt

4.

Spring loaded idler pulley

Replacing and Tensioning the
Alternator Belt

Replacing the Alternator Belt

Service Interval:

Every 50 hours—Check the alternator

belt.

If the alternator belt needs to be replace, take your
machine to an Authorized Service Dealer.

Tensioning the Alternator Belt

1. Place a handle between the alternator and cylinder

block.

2. Adjust the alternator to the outside until there is

1/4 to 11/32 inch (7 to 9 mm) deflection in the belt
between the engine and the alternator pulleys with
22.1 lbs of force (10 kgf) (Figure 72).

3. Tighten the alternator bolts.

4. Check the deflection in the belt again and adjust the

belt if needed.

5. If the deflection is correct, tighten the bottom and

upper bolt (Figure 72).

Figure 72

1.

Alternator

4.

Top bolt

2.

Alternator belt

5.

Bottom bolt

3.

Deflection, 1/4 to
11/32 inch (7 to 9 mm) with
22.1 lbs of force (10 kgf)

51

Содержание Z580-D Z Master 74266





































































Отзывы:

Нет отзывов