Toro Z580-D Z Master 74266 Скачать руководство пользователя страница 63

Страница: 63 / 68

Troubleshooting

Problem

Possible Cause

Corrective Action

1. The blade control (PTO) is engaged.

1. Move the blade control (PTO) to the

disengaged position.

2. The parking brake is not on.

2. Set the parking brake.

3. The operator is not seated.

3. Sit on the seat.

4. The battery is dead.

4. Charge the battery.

5. The electrical connections are corroded

or loose.

5. Check the electrical connections for

good contact.

6. The fuse is blown.

6. Replace the fuse.

The starter does not crank.

7. The relay or switch is defective.

7. Contact an Authorized Service Dealer.

1. The fuel tank is empty.

1. Fill the fuel tank with fuel.

2. The air cleaner is dirty.

2. Clean or replace the air cleaner

element.

3. Dirt is in the fuel filter.

3. Replace the fuel filter.

The engine will not start, starts hard, or
fails to keep running.

4. Dirt, water, or stale fuel is in the fuel

system.

4. Contact an Authorized Service Dealer.

1. The engine load is excessive.

1. Reduce the ground speed.

2. The air cleaner is dirty.

2. Clean the air cleaner element.

3. The oil level in the crankcase is low.

3. Add oil to the crankcase.

4. The cooling fins and air passages

above the engine are plugged.

4. Remove the obstruction from the

cooling fins and air passages.

5. The vent hole in the fuel cap is plugged.

5. Clean or replace the fuel cap.

6. Dirt is in the fuel filter.

6. Replace the fuel filter.

The engine loses power.

7. Dirt, water, or stale fuel is in the fuel

system.

7. Contact an Authorized Service Dealer.

1. The engine load is excessive.

1. Reduce the ground speed.

2. The oil level in the crankcase is low.

2. Add oil to the crankcase.

The engine overheats.

3. The cooling fins and air passages

above the engine are plugged.

3. Remove the obstruction from the

cooling fins and air passages.

1. The by pass valve is not closed tight.

1. Tighten the by pass valve.

2. The drive or pump belt is worn, loose

or broken.

2. Change the belt.

3. The drive or pump belt is off a pulley.

3. Change the belt.

4. The idler spring is broken or missing.

4. Replace the spring.

The machine does not drive.

5. The hydraulic fluid level is low or too

hot.

5. Add hydraulic fluid to the reservoir or

let it cool down.

1. The cutting blade(s) is/are bent or

unbalanced.

1. Install new cutting blade(s).

2. The blade mounting bolt is loose.

2. Tighten the blade mounting bolt.

3. The engine mounting bolts are loose.

3. Tighten the engine mounting bolts.

4. The engine pulley, idler pulley, or blade

pulley is loose.

4. Tighten the appropriate pulley.

5. The engine pulley is damaged.

5. Contact an Authorized Service Dealer.

6. The blade spindle is bent.

6. Contact an Authorized Service Dealer.

Abnormal vibration.

7. The motor mount is loose or worn.

7. Contact an Authorized Service Dealer.

Содержание Z580-D Z Master 74266





































































Результаты поиска

Содержание Z580-D Z Master 74266

Отзывы:

Похожие инструкции для Z580-D Z Master 74266

Бренды по названию

Популярные бренды

Toro Z580-D Z Master 74266, Руководство оператора

Результаты поиска

Содержание Z580-D Z Master 74266

Отзывы:

Похожие инструкции для Z580-D Z Master 74266

Бренды по названию

Популярные бренды