Toro Z580-D Z Master 74266 Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 68

background image

WARNING

Hydraulic fluid escaping under pressure can
penetrate skin and cause injury.

•

If hydraulic fluid is injected into the skin it
must be surgically removed within a few hours
by a doctor familiar with this type of injury.
Gangrene may result if this is not done.

•

Keep body and hands away from pin hole leaks
or nozzles that eject high pressure hydraulic
fluid.

•

Use cardboard or paper to find hydraulic leaks.

•

Safely relieve all pressure in the hydraulic system
before performing any work on the hydraulic
system.

•

Make sure all hydraulic fluid hoses and lines are
in good condition and all hydraulic connections
and fittings are tight before applying pressure to
hydraulic system.

Setting the Hydraulic Pump
Neutral Position

Note:

Adjust the handle neutral first. That needs to be

correct before the following adjustment can be made.

This adjustment must be made with drive wheels turning.

DANGER

Mechanical or hydraulic jacks may fail to support
machine and cause a serious injury.

•

Use jack stand when supporting machine.

•

Do not use hydraulic jacks.

WARNING

Engine must be running so motion control
adjustment can be performed. Contact with moving
parts or hot surfaces may cause personal injury.

Keep hands, feet, face, clothing and other body
parts away from rotating parts, muffler and other
hot surfaces.

1. Raise the frame and block up the machine so drive

wheels can rotate freely.

2. Disconnect the electrical connector from the seat

safety switch. Temporarily install a jumper wire
across terminals in the wiring harness connector.

3. Unlatch the seat and slide seat forward.

4. Disconnect the seat rod and tilt the seat fully forward.

Setting the Right-hand Hydraulic Pump
Neutral Position

1. Start the engine, open the throttle 1/2 way and

release parking brake. Refer to Starting and Stopping
the Engine in Operation.

Note:

The motion control lever must be in neutral

while making any adjustments.

2. Adjust the pump rod length by rotating the knob, in

the appropriate direction, until the wheel is still or
slightly creeping in reverse (Figure 78).

3. Move the motion control lever forward and reverse,

then back to neutral. The wheel must stop turning
or slightly creep in reverse.

4. Open the throttle to fast. Make sure wheel remains

stopped or slightly creeps in reverse, adjust if
necessary.

Figure 78

1.

Tracking knob

4.

Turn this way to track right

2.

Hydraulic tank

5.

Turn this way to track left

3.

Hydraulic pumps

Setting the Left-hand Hydraulic Pump
Neutral Position

1. Loosen the locknuts at the ball joints on the pump

control rod (Figure 79).

55

«
...
53
54
55
56
57
...
»

Содержание Z580-D Z Master 74266





































































Отзывы:

Нет отзывов

Похожие инструкции для Z580-D Z Master 74266

Бренд: Kärcher Страницы: 12

GLM 40/124 P EASY

Бренд: F.F. Group Страницы: 128

Бренд: Jacobsen Страницы: 118

Бренд: Sabo Страницы: 100

Бренд: Bolens Страницы: 32

Бренд: Dixon Страницы: 13

Бренд: Troy-Bilt Страницы: 52

AutoDrive 60-1827-4

Бренд: Yard Works Страницы: 53

Бренд: Poulan Pro Страницы: 48

Бренд: Kraftixx Страницы: 246

COMPANION 917.385170

Бренд: COMPANION Страницы: 40

Бренд: EINHELL Страницы: 288

Бренд: Toro Страницы: 40

Бренд: Fort Страницы: 100

Бренд: Exmark Страницы: 32

Бренд: Scheppach Страницы: 60

Turbo Compact TC330

Бренд: Flymo Страницы: 9

Бренд: Flymo Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды