Toro Z580-D Z Master 74266 Скачать руководство пользователя страница 13

Страница: 13 / 68

Battery Symbols

Some or all of these symbols are on your battery

Explosion hazard

Keep bystanders a safe
distance from the battery.

No fire, open flame, or
smoking.

Wear eye protection;
explosive gases can
cause blindness and other
injuries

Caustic liquid/chemical
burn hazard

Battery acid can cause
blindness or severe burns.

Wear eye protection

Flush eyes immediately
with water and get medical
help fast.

Read the

Operator’s

Manual.

10.

Contains lead; do not
discard.

107-3963

Cutting/dismemberment
hazard, mower blade—do
not carry passengers and
keep bystanders away.

Cutting/dismemberment
hazard of hand or foot,
mower blade—remove
the ignition key and read
the instructions before
servicing or performing
maintenance; stay away
from moving parts.

Thrown object
hazard—keep bystanders
a safe distance from the
machine and keep the
deflector in place.

Before starting the engine,
clean grass and debris from
the mower belt and pulleys,
insert the ignition key, and
start the engine.

Содержание Z580-D Z Master 74266





































































Результаты поиска

Содержание Z580-D Z Master 74266

Отзывы:

Похожие инструкции для Z580-D Z Master 74266

Бренды по названию

Популярные бренды

Toro Z580-D Z Master 74266, Руководство оператора

Результаты поиска

Содержание Z580-D Z Master 74266

Отзывы:

Похожие инструкции для Z580-D Z Master 74266

Бренды по названию

Популярные бренды