Toro Z580-D Z Master 74266 Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 68

background image

Maintenance

Recommended Maintenance Schedule(s)

Maintenance Service

Interval

Maintenance Procedure

After the first 8 hours

• Check the engine cooling system level.
• Check the hydraulic fluid level.

After the first 25 hours

• Change the hydraulic filter.

After the first 50 hours

• Change the engine oil.
• Change the engine oil filter.

After the first 100 hours

• Check the wheel hub slotted nut.
• Check the wheel lug nuts.
• Change gear box oil.

Before each use or daily

• Check the safety system.
• Check the engine oil.
• Check the engine cooling system level.
• Clean the engine oil cooler.
• Check the mower blades.
• Clean the mower deck.

Every 25 hours

• Grease the mower deck and spindles.
• Grease the mower belt idler arm.
• Grease the pump belt idler arm.
• Grease the PTO drive belt idler arm.
• Grease the brake lever.
• Check the hydraulic fluid level.

Every 40 hours

• Drain the water separator.

Every 50 hours

• Check the tire pressure. or monthly, whichever occurs first.
• Check the PTO drive belt.
• Check the pump drive belt.
• Check the alternator belt.

Every 100 hours

• Change the engine oil.
• Check the gear box oil level.
• Check the engine cooling system hoses.
• Inspect the belts for cracks and wear.
• Check the hydraulic hoses.

Every 150 hours

• Lubricate the machine with light oil (Refer to Lubrication).

Every 200 hours

• Change the engine oil filter.
• Grease the brake pivot.

Every 250 hours

• Check and/or replace the air filter (more often in dirty or dusty conditions).
• Change the hydraulic filter and hydraulic oil when using Mobil® 1 oil.

Every 500 hours

• Check the wheel hub slotted nut.
• Check the wheel lug nuts.
• Adjust the caster pivot bearing.
• Adjust the electric clutch.
• Change the hydraulic filter and hydraulic oil when using Toro® HYPR-OIL™ 500

hydraulic oil.

Yearly

• Grease the front caster pivots (more often in dirty or dusty conditions).
• Change the gear box oil.
• Change the engine coolant.

Important:

Refer to your

Engine Operator’s Manual

for additional maintenance procedures.

32

«
...
30
31
32
33
34
...
»

Содержание Z580-D Z Master 74266





































































Отзывы:

Нет отзывов

Похожие инструкции для Z580-D Z Master 74266

Бренд: Yard-Man Страницы: 32

PowerMax 1200/32

Бренд: Gardena Страницы: 352

Бренд: Gardif Страницы: 21

Бренд: Snapper Страницы: 40

Silver Series 10270

Бренд: Lawn-Boy Страницы: 29

Бренд: Nakayama Страницы: 19

Бренд: Poulan Pro Страницы: 4

Бренд: Snapper Страницы: 256

Бренд: Cub Cadet Страницы: 2

Бренд: Gardenline Страницы: 17

Бренд: Black+Decker Страницы: 12

28HP Tank 53AB5JEZ630

Бренд: Cub Cadet Страницы: 36

Бренд: Bushranger Страницы: 14

Бренд: Snapper Страницы: 15

Бренд: Snapper Страницы: 24

Бренд: Snapper Страницы: 12

Бренд: Snapper Страницы: 52

Бренд: Snapper Страницы: 54

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды