Toro Z580-D Z Master 74266 Скачать руководство пользователя страница 64

Страница: 64 / 68

Problem

Possible Cause

Corrective Action

1. The cutting blade(s) is/are not sharp.

1. Sharpen the blade(s).

2. The cutting blade(s) is/are bent.

2. Install new cutting blade(s).

3. The mower deck is not level.

3. Level the mower deck from side-to-side

and front-to-rear.

4. The underside of mower is dirty.

4. Clean the underside of the mower.

5. The tire pressure is not correct.

5. Adjust the tire pressure.

Uneven cutting height.

6. The blade spindle is bent.

6. Contact an Authorized Service Dealer.

1. The drive belt is worn, loose or broken.

1. Check the belt tension.

2. The drive belt is off pulley.

2. Install the drive belt and check

adjusting shafts and belt guides for
correct position.

3. The mower deck belt is worn, loose or

broken.

3. Install a new mower deck belt.

4. The mower deck belt came off a pulley.

4. Install mower deck belt and check the

idler pulley, idler arm and spring for the
correct position and function.

The cutting blades do not rotate.

5. The idler spring is broken or missing.

5. Replace the spring.

Содержание Z580-D Z Master 74266





































































Результаты поиска

Содержание Z580-D Z Master 74266

Отзывы:

Похожие инструкции для Z580-D Z Master 74266

Бренды по названию

Популярные бренды

Toro Z580-D Z Master 74266, Руководство оператора

Результаты поиска

Содержание Z580-D Z Master 74266

Отзывы:

Похожие инструкции для Z580-D Z Master 74266

Бренды по названию

Популярные бренды