manualshive.com logo in svg

Toro Z580-D Z Master 74266, Руководство оператора, Страница: 56 / 68

Поделиться
Скачать
Toro Z580-D Z Master 74266 Скачать руководство пользователя страница 56

2. Start the engine, open throttle 1/2 way and release

parking brake. Refer to Starting and Stopping the
Engine in Operation.

Note:

The motion control lever must be in neutral

while making any adjustments.

Note:

The front nut on the pump rod has left-hand

threads.

3. Adjust the pump rod length by rotating double nuts

on rod, in the appropriate direction, until wheel is
still or slightly creeps in reverse (Figure 79).

4. Move the motion control lever forward and reverse,

then back to neutral. The wheel must stop turning
or slightly creep in reverse.

5. Open the throttle to fast. Make sure the wheel

remains stopped or slightly creeps in reverse, adjust
if necessary.

6. Tighten the locknuts at the ball joints (Figure 79).

Figure 79

1.

Double nuts

4.

Locknut

2.

Pump rod

5.

Ball joint

3.

Adjustment bolt

6.

Pumps

WARNING

Electrical system will not perform proper safety
shut off with jumper wire installed.

•

Remove jumper wire from wire harness
connector and plug connector into seat
switch when adjustment is completed.

•

Never operate this unit with jumper installed
and seat switch bypassed.

7. After both pump neutrals are set, shut off the

machine.

8. Remove the jumper wire from the wire harness

connector and plug the connector into the seat
switch.

9. Install the seat rod and lower the seat into position.

10. Remove the jack stands.

56

Содержание Z580-D Z Master 74266





































































Отзывы:

Нет отзывов