Toro Z580-D Z Master 74266 Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 68

Toro Z580-D Z Master 74266 Скачать руководство пользователя страница 48

Figure 65

1.

Hydraulic oil cooler

3.

Radiator screen

2.

Left rear tire

Changing the Engine Coolant

Service Interval:

Yearly

Have an Authorized Service Dealer change the engine
coolant every year.

Brake Maintenance

Adjusting the Parking Brake

Service Interval:

Every 25 hours

Every 200 hours

1. Engage the parking brake, lever up.

2. Measure the length of the spring. Measurement

should be 2-1/2 inch (64 mm) between the washers
(Figure 66).

3. If adjustment is necessary, release the parking brake,

loosen the jam nut below the spring and adjust the
nut directly below the spring (Figure 66). Turn the
nut until the correct measurement is obtained. Turn
the nut clockwise to shorten spring length and turn
counter-clockwise to lengthen the spring.

4. Tighten the two nuts together.

5. Engage the parking brake, lever up. Check the

measurement of the spring again.

6. If adjustment is necessary, repeat the procedures

above.

7. Repeat on the opposite side of machine.

Figure 66

1.

Brake lever in engaged
position

3.

Adjusting nut and jam nut

2.

Spring 2–1/2 inch (64 mm)

48

«
...
46
47
48
49
50
...
»

Содержание Z580-D Z Master 74266





































































Отзывы:

Нет отзывов