Toro Groundsmaster 4300-D Скачать руководство пользователя страница 5

Страница: 5 / 80

Safety and Instructional Decals

Safety decals and instructions are easily visible to the operator and are located near any area
of potential danger. Replace any decal that is damaged or missing.

decal93-6681

93-6681

Cutting/dismemberment hazard, fan—stay away from
moving parts.

decal93-6689

93-6689

Warning—do not carry passengers.

decal93-7272

93-7272

Cutting/dismemberment hazard; fan—stay away from
moving parts.

decal93-7818

93-7818

Warning—read the

Operator's Manual

for instructions on

torquing the blade bolt/nut to 115 to 149 N∙m (85 to 110
ft-lb).

decal106-6754

106-6754

Warning—do not touch the hot surface.

Cutting/dismemberment hazard, fan and entanglement
hazard, belt—stay away from moving parts.

decal106-6755

106-6755

Engine coolant under
pressure.

Warning—do not touch the
hot surface.

Explosion hazard—read
the

Operator's Manual.

Warning—read the

Operator's Manual.

decal110-0986

110-0986

Press the brake pedal and parking-brake pedal to engage
the parking brake.

Press the brake pedal to apply the brake.

Press the traction pedal to move the machine forward.

PTO enabled mode

Transport mode (No PTO)

decal110-8921

110-8921

Traction unit speed

Slow

Fast

Содержание Groundsmaster 4300-D

















































































Результаты поиска

Содержание Groundsmaster 4300-D

Отзывы:

Похожие инструкции для Groundsmaster 4300-D

Бренды по названию

Популярные бренды

Toro Groundsmaster 4300-D, Руководство оператора

Результаты поиска

Содержание Groundsmaster 4300-D

Отзывы:

Похожие инструкции для Groundsmaster 4300-D

Бренды по названию

Популярные бренды