Toro Groundsmaster 4300-D Скачать руководство пользователя страница 65

Страница: 65 / 80

that the cable conduit does not rotate during
tightening procedure.

Adjusting the
Parking-Brake Latch

If the parking brake fails to engage and latch, an
adjustment to the brake pawl is required.

Loosen the 2 screws securing the parking brake
pawl to the frame (

Figure 91

g031690

Figure 91

Brake cables

Parking brake pawl

Brake detent

Screws (2)

Press the parking brake pedal forward until the
brake detent completely engages on the brake
pawl (

Figure 91

Tighten the 2 screws locking the adjustment.

Press the brake pedal to disengage the parking
brake.

Check the adjustment and adjust as required.

Belt Maintenance

Servicing the Alternator
Belt

Service Interval:

After the first 10 hours

Every 100 hours

Note:

For proper belt tension, allow 10 mm (3/8 inch)

deflection when a force of 44 N (10 lb) is applied on
the belt midway between the pulleys.

If the deflection is not 10 mm (3/8 inch), loosen
the alternator mounting bolts (

Figure 92

g020537

Figure 92

Mounting bolt

Alternator

Increase or decrease the alternator-belt tension
and tighten the bolts.

Check the deflection of the belt again to ensure
that the tension is correct.

Содержание Groundsmaster 4300-D

















































































Результаты поиска

Содержание Groundsmaster 4300-D

Отзывы:

Похожие инструкции для Groundsmaster 4300-D

Бренды по названию

Популярные бренды

Toro Groundsmaster 4300-D, Руководство оператора

Результаты поиска

Содержание Groundsmaster 4300-D

Отзывы:

Похожие инструкции для Groundsmaster 4300-D

Бренды по названию

Популярные бренды