Toro Groundsmaster 4300-D Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 80

background image

Description

reference

Dimension or Weight

Overall height

A

217 cm (85.5 inches)

Wheel tread (tire center to center) rear

B

185 cm (72.5 inches)

Overall width (transport position)

C

231 cm (91 inches)

Overall width (mowing position)

D

247 cm (97 inches)

Wheel base

E

152 cm (60 inches)

Overall length (transport position)

F

315 cm (124 inches)

Overall length (mowing position)

G

315 cm (124 inches)

Fuel-tank capacity

51 L (13.5 US gallons)

Transport speed

0 to 16 km/h (0 to 10 mph)

Mowing speed

0 to 13 km/h (0 to 8 mph)

Net weight (with cutting decks and fluids)

1492 kg (3,289 lb)

Cutting Unit Specifications

Length

86.4 cm (34 inches)

Width

86.4 cm (34 inches)

Height

24.4 cm (9.6 inches) to carrier mount
26.7 cm (10–1/2 inches) at 3/4 inch height of cut
34.9 cm (13–3/4 inches) at 4 inch height of cut

Weight

88 kg (195 lb)

Attachments/Accessories

A selection of Toro approved attachments and accessories is available for use with the machine to enhance
and expand its capabilities. Contact your Authorized Service Dealer or authorized Toro distributor or go to
www.Toro.com for a list of all approved attachments and accessories.

To ensure optimum performance and continued safety certification of the machine, use only genuine Toro
replacement parts and accessories. Replacement parts and accessories made by other manufacturers could be
dangerous, and such use could void the product warranty.

25

«
...
23
24
25
26
27
...
»

Содержание Groundsmaster 4300-D

















































































Отзывы:

Нет отзывов

Похожие инструкции для Groundsmaster 4300-D

Бренд: Makita Страницы: 17

Бренд: Makita Страницы: 13

Бренд: Xoop Lighting Страницы: 20

Бренд: Vari Lite Страницы: 132

Бренд: ACE INSTRUMENTS Страницы: 2

Бренд: ODA Страницы: 103

Бренд: LAWO Страницы: 459

Бренд: earline Страницы: 13

AquaPure Ei Series

Бренд: Jandy Страницы: 4

AquaPure Ei Series

Бренд: Jandy Страницы: 8

Jandy Pro Series

Бренд: Jandy Страницы: 16

ThermoTweez Handpiece TT-65

Бренд: Pace Страницы: 14

Бренд: R&S Страницы: 371

Бренд: R.M. Young Страницы: 9

Бренд: Reflex Marine Страницы: 36

MEGA STROBE/DMX

Бренд: American DJ Страницы: 2

Бренд: American DJ Страницы: 8

Бренд: COURANT Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды