TKH Skilleye SEP-FRTMP01 Скачать руководство пользователя | Manualshive

Страница: 43 / 65

background image

37

Temperature Measurement & Face Recognition Terminal User Manual

6.4.2 Port

Go to Config

→

Network

→

Port interface as shown below. HTTP port, Data port and RTSP port

can be set.

HTTP Port

: The default HTTP port is 80. It can be changed to any port which is not occupied.

HTTPS Port

: The default HTTPs port is 443. It can be changed to any port which is not

occupied.

Data Port

: The default data port is 9008. Please change it as necessary.

RTSP Port

: The default port is 554. Please change it as necessary.

6.4.3 Server Configuration

This function is mainly used for connecting network video management system.

1. Check “Enable”.
2. Check the IP address and port of the transfer media server in the ECMS/NVMS. Then
enable the auto report in the ECMS/NVMS when adding a new device. Next, enter the
remaining information of the device in the ECMS/NVMS. After that, the system will
automatically allot a device ID. Please check it in the ECMS/NVMS.
3. Enter the above-mentioned server address, server port and device ID in the corresponding
boxes. Click the “Save” button to save the settings.

6.4.4 DDNS

If the camera is set up with a DHCP connection, DDNS should be set for the internet.
1. Go to Config

→

Network

→

DDNS.

«
...
41
42
43
44
45
...
»

Содержание Skilleye SEP-FRTMP01


































































Отзывы:

Нет отзывов

Похожие инструкции для Skilleye SEP-FRTMP01

Бренд: Nab Страницы: 20

Бренд: Magtek Страницы: 26

Бренд: Magtek Страницы: 35

Бренд: Baracoda Страницы: 35

Бренд: FlyTech Страницы: 25

Tashi MT380 Proximity

Бренд: Unitech Страницы: 14

Бренд: ECKELMANN Страницы: 61

Бренд: Pepperl+Fuchs Страницы: 30

MSR JC-1290 KB series

Бренд: Glancetron Страницы: 30

Бренд: Tatung Страницы: 84

Бренд: Denso Страницы: 166

Бренд: OBO Bettermann Страницы: 126

Бренд: SCM Страницы: 9

Бренд: IBM Страницы: 68

RealPOS 72XRT POS

Бренд: NCR Страницы: 202

Бренд: Kensington Страницы: 6

Бренд: Kensington Страницы: 8

Бренд: 3nStar Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды