TKH Skilleye SEP-FRTMP01 Скачать руководство пользователя | Manualshive

Страница: 38 / 65

background image

32

Temperature Measurement & Face Recognition Terminal User Manual

the system responds to the blurriness of the image.

The sensitivity value of Video Color Cast Detection

: The higher the value is, the more

sensitive the system responds to the obscuring of the image.

6.3.2 SD Card Full

1. Go to Config

→

Alarm

→

Anomaly

→

SD Card Full.

2. Click “Enable” and set the alarm holding time.
3. Set alarm trigger options. The setup steps are the same as temperature measurement
settings. Please refer to temperature measurement settings chapter for details.

6.3.3 SD Card Error

When there are some errors in writing to the SD card, the corresponding alarms will be triggered.
1. Go to Config

→

Alarm

→

Anomaly

→

SD Card Error as shown below.

2. Click “Enable” and set the alarm holding time.
3. Set alarm trigger options. Trigger alarm out, Email and FTP. The setup steps are the same

«
...
36
37
38
39
40
...
»

Содержание Skilleye SEP-FRTMP01


































































Отзывы:

Нет отзывов

Похожие инструкции для Skilleye SEP-FRTMP01

Бренд: IBM Страницы: 206

Бренд: Quest Payment Systems Страницы: 37

Tashi MT380 Proximity

Бренд: Unitech Страницы: 14

Бренд: Network Computing Devices Страницы: 45

First Data A920

Бренд: Fiserv Страницы: 6

Бренд: National Instruments Страницы: 4

Бренд: National Instruments Страницы: 12

Бренд: IDTECH Страницы: 35

Бренд: Wincor Nixdorf Страницы: 43

Бренд: BURGER KING Страницы: 20

Бренд: POSIFLEX Страницы: 50

Бренд: UTC RETAIL Страницы: 9

Бренд: UTC RETAIL Страницы: 12

Бренд: SCM Microsystems Страницы: 78

Бренд: Raisecom Страницы: 61

Бренд: MVG industries Страницы: 22

Бренд: MVG Страницы: 36

Бренд: QUORION Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды