TKH Skilleye SEP-FRTMP01 Скачать руководство пользователя | Manualshive

Страница: 42 / 65

background image

36

Temperature Measurement & Face Recognition Terminal User Manual

Use IP address (take IPv4 for example)-

There are two options for IP setup: obtain an IP

address automatically by DHCP and use the following IP address. Please choose one of the
options as needed.
Test: Test the effectiveness of the IP address by clicking this button.

Use PPPoE-

Click the “PPPoE Config” tab to go to the interface as shown below. Enable PPPoE

and then enter the user name and password from your ISP.

Either  method  of  network  connection  can be  used.  If  PPPoE  is used  to  connect  internet,  the
camera  will  get  a  dynamic  WAN  IP  address.  This  IP  address  will  change  frequently.  To  be
notified, the IP change notification function can be used.
Click “IP Change Notification Config” to go to the interface as shown below.

Trigger Email

: when the IP address of the device is changed, the new IP address will be sent

to the email address that has been set up.

Trigger FTP

: when the IP address of the device is changed, the new IP address will be sent to

FTP server that has been set up.

«
...
40
41
42
43
44
...
»

Содержание Skilleye SEP-FRTMP01


































































Отзывы:

Нет отзывов

Похожие инструкции для Skilleye SEP-FRTMP01

Бренд: Partner Страницы: 61

Бренд: Partner Страницы: 56

Бренд: Partner Страницы: 78

Бренд: Partner Страницы: 50

Бренд: Partner Страницы: 2

Бренд: eTung Страницы: 52

Бренд: Wincor Nixdorf Страницы: 20

Бренд: SkyWave Страницы: 64

Бренд: JAO TECH Страницы: 44

Бренд: Wincor Nixdorf Страницы: 97

ABOX-110 Series

Бренд: AdvanPOS Страницы: 43

Бренд: Jamex Страницы: 14

Бренд: National Instruments Страницы: 14

Бренд: Hanasis Страницы: 11

Бренд: EBN Страницы: 50

POS50A-5B-LX800

Бренд: EBN Страницы: 20

Бренд: Omni Страницы: 2

Бренд: Unitech Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды