TKH Skilleye SEP-FRTMP01 Скачать руководство пользователя | Manualshive

Страница: 40 / 65

background image

34

Temperature Measurement & Face Recognition Terminal User Manual

1. Select the sensor ID, click “Enable” and set the alarm type, alarm holding time and sensor
name.
2. Set alarm trigger options. The setup steps are the same as temperature measurement
settings. Please refer to temperature measurement settings chapter for details.
3. Click “Save” button to save the settings.
4. Set the schedule of the sensor alarm. The setup steps of the schedule are the same as the
schedule recording setup. (See Schedule Recording).
Click “Apply settings to” to quickly apply the settings to the other alarm input.

6.3.7 Alarm Out

Go to Config

→

Alarm

→

Alarm Out.

Alarm Out ID:

Select the alarm out ID.

Alarm Out Mode

: Alarm linkage, manual operation, day/night switch linkage and timing are

optional.

Alarm Linkage

: Having selected this mode, select alarm out name, alarm holding time at the

“Alarm Holding Time” pull down list box and alarm type.

Manual Operation

: Having selected this mode, select the alarm type and click “Open” to

«
...
38
39
40
41
42
...
»

Содержание Skilleye SEP-FRTMP01


































































Отзывы:

Нет отзывов

Похожие инструкции для Skilleye SEP-FRTMP01

Бренд: IBM Страницы: 148

Бренд: bnz Страницы: 6

Бренд: LIVE TAXIEPAY Страницы: 2

Бренд: Axon Страницы: 62

Бренд: Tcang Страницы: 13

Бренд: National Instruments Страницы: 12

Бренд: National Instruments Страницы: 12

Бренд: Russound Страницы: 2

Бренд: Partner Страницы: 2

Бренд: Zte Страницы: 27

Morpho RapID Series

Бренд: Sagem Securite Страницы: 13

Бренд: Harris Страницы: 96

Бренд: CC-ISOBUS Страницы: 412

Бренд: LXE Страницы: 29

Бренд: Datapath Страницы: 104

Бренд: VendNet Страницы: 6

Бренд: Zebex Страницы: 2

Бренд: Western Telematic Страницы: 54

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды