TKH Skilleye SEP-FRTMP01 Скачать руководство пользователя

Страница: 13 / 65

Temperature Measurement & Face Recognition Terminal User Manual

Router Setup

④

Open the IE browser and enter its WAN IP and http port to access. (for example, if the http

port is changed to 81, please enter “192.198.1.201:81” in the address bar of web browser to
access).

➢

Access through PPPoE dial-up

Network connection

Access the camera through PPPoE auto dial-up. The setup steps are as follow:

①

Go to Config

→

Network

→

Port menu to set the port number.

②

Go to Config

→

Network

→

TCP/IP

→

PPPoE Config menu. Enable PPPoE and then enter the

user name and password from your internet service provider.

③

Go to Config

→

Network

→

DDNS menu. Before configuring the DDNS, please apply for a

domain name first. Please refer to DDNS configuration for detail information.

④

Open the IE browser and enter the domain name and http port to access.

Содержание Skilleye SEP-FRTMP01


































































Результаты поиска

Содержание Skilleye SEP-FRTMP01

Отзывы:

Похожие инструкции для Skilleye SEP-FRTMP01

Бренды по названию

Популярные бренды

TKH Skilleye SEP-FRTMP01, Руководство пользователя

Результаты поиска

Содержание Skilleye SEP-FRTMP01

Отзывы:

Похожие инструкции для Skilleye SEP-FRTMP01

Бренды по названию

Популярные бренды