13
SYStem DeSCription
HELIX
3.5
INSTAllINg The cIrculATIoN KIT
(opTIoNAl)
i
The circulation kit is available for separate
purchase. Follow the steps below to install it.
Refer to section 2.2 for Clearance Diagram.
1. Make sure the system is turned off and depressurized.
2. Remove the two inlet plugs (Fig. 4, item 1) from the bottom
of the hose heater manifold. Remove return tubes (2).
3. Thread a shut-off valve (Fig. 3, item L1) from the circulation
kit into each of the ports underneath the hose heater
manifold. Thread the longer return tubes (Fig. 2, item F)
underneath each of the PRIME/SPRAY valve manifolds.
4. Attach a hose to each of the shut-off valves. Run the
hoses (Fig. 3, item L2) and return hoses (Fig. 3, item F)
back towards the material containers and thread into their
respective ports on the desiccant dryers.
1
2
3.4
compoNeNT DeScrIpTIoN - WITh cIrculATIoN
i
This configuration is only possible with the purchase of
circulation kit P/N 0138914, sold separately. The parts
included in the kit are labeled with an asterisk (*).
ITem DeScrIpTIoN
fuNcTIoN
A
Component Pump A
In a two-component system, Component Pump A typically pumps the ISO or activator material.
B
Component Pump B
In a two-component system, Component Pump B typically pumps the resin material.
c
Surefire™ Heater Block
Material flows from the supply containers into the fluid pumps, where the material is pressurized to
the desired pressure(s), based on the Control Panel settings. The Surefire™ heater block heats the
material on its way to the material pumps.
D
Control Panel
The control panel contains all of the system controls that allow the sprayer to function properly, as
well as being the main display panel that gives information about the system.
e
PRIME/SPRAY knob
The PRIME/SPRAY knob directs material to the spray hose when in the SPRAY position and to the
prime hoses when in the PRIME position. Turning the PRIME/SPRAY knob will relieve any pressure
built up in the system.
f
Prime hoses
When the PRIME/SPRAY knobs are set to PRIME, spray material will circulate into the Component
pumps and then out of the prime hoses.
g
Inlet valves
The inlet valves allow material to be drawn from the material containers into the system. They can
be turned off in order to prevent material from entering the system.
h
Supply hoses
The two supply hoses deliver fluid from the supply drums to the Component pumps.
I
Dual heated hose
The dual heated hose delivers spray material from the two Component Pumps to the spray gun.
j
Transfer pump
The two transfer pumps pump material from the supply containers, into the supply hoses and then
to the Component Pumps. The transfer pumps are powered by an air compressor.
K
Desiccant dryer
The Desiccant dryers remove any moisture that is present in the air pockets left by the removal of
material from the supply drums.
l*
Circulation valves / hoses
When open, the circulation valves (L1) allow material to circulate through the heater block and
back through the hoses (L2) into the supply containers. This allows the material to be heated more
quickly.
m
Transfer pump air hose
The transfer pump air hose delivers air from the compressor to the transfer pumps.
N
Agitator
The agitator stirs the material on the resin (B) side material container.
Содержание HELIX 0138011
Страница 12: ...12 SYSTEM DESCRIPTION HELIX A E D F L1 J H K K J N M M B H L2 G I C 3 3 System Diagram with circulation ...
Страница 44: ...44 HELIX Spare parts diagram drive assembly 4 5 6 1 2 3 7 8 9 10 11 18 17 12 13 14 15 16 ...
Страница 50: ...50 HELIX Spare parts diagram fluid section 1 2 3 4 7 8 15 16 17 18 19 20 21 22 23 9 10 11 12 13 14 5 6 ...