![background image](http://html1.mh-extra.com/html/titan/helix-0138011/helix-0138011_operating-manual_1119425007.webp)
7
SaFetY regulationS
HELIX
i
The amount of film formation and the rate of
crystalization varies depending upon the blend
of ISO, the humidity and the temperature.
preveNTIoN:
•
Always use a sealed container with a desiccant dryer in
the vent, or a nitrogen atmosphere. NEVER store ISO in an
open container.
•
Use ONLY the moisture-proof hoses specifically designed
for ISO that are supplied with your system. If new hoses
need to be ordered, contact Titan Technical Service.
•
Never flush reclaimed solvents through the system.
Reclaimed solvents can contain moisture. Always keep
solvent containers closed when not being used to prevent
moisture contamination.
•
Never use solvent on one side if it has been contaminated
from the other side.
•
Always lubricate threaded parts with ISO pump oil or
grease when reassembling.
•
Always circulate a hose and pump that contains ISO at least
once a week to prevent the ISO from crystalizing.
chANgINg mATerIAlS
•
When changing spray materials, thoroughly flush the
equipment multiple times to ensure that it is fully clean.
•
Always clean the fluid inlet strainers after flushing.
•
Check with your material manufacturer for chemical
compatibility.
•
Most materials use ISO with Component A, but some use
ISO with Component B.
•
Epoxies often have amines (hardener) with Component B.
Polyureas often have amines with Component B (resin).
foAm reSINS WITh 245fA BloWINg AgeNT
Some blowing agents will froth at temperatures above 90º
F (33ºC) when not under pressure, especially if agitated. To
reduce frothing, minimize preheating in a circulation system.
1.3
elecTrIc SAfeTy
Electric models must be earthed. In the event of an electrical
short circuit, earthing reduces the risk of electric shock by
providing an escape wire for the electric current. Connection
to the mains only through a special feed point, e.g. through an
error protection insallation with INF < 30 mA.
DANGER — Work or repairs at the electrical
equipment may only be carried out by a skilled
electrician. No liability is assumed for incorrect
installation. Switch the unit off. Before all repair
work, unplug the power plug from the outlet.
Danger of short-circuits caused by water
ingressing into the electrical equipment. Never
spray down the unit with high-pressure or high-
pressure steam cleaners.
operATINg TemperATure
This equipment will operate correctly in its intended ambient,
at a minimum b10°C and +40°C.
relATIve humIDITy
The equipment will operate correctly within an environment
at 50% RH, +40°C. Higher RH may be allowed at lower
temperatures.
Measures shall be taken by the Purchaser to avoid the harmful
effects of occasional condensation.
AlTITuDe
This equipment will operate correctly up to 2100 m above
mean sea level.
TrANSporTATIoN AND STorAge
This equipment will withstand, or has been protected against,
transportation and storage temperatures of -25°C to +55°C and
for short periods up to +70°C.
It has been packaged to prevent damage from the effects of
normal humidity, vibration and shock.
Содержание HELIX 0138011
Страница 12: ...12 SYSTEM DESCRIPTION HELIX A E D F L1 J H K K J N M M B H L2 G I C 3 3 System Diagram with circulation ...
Страница 44: ...44 HELIX Spare parts diagram drive assembly 4 5 6 1 2 3 7 8 9 10 11 18 17 12 13 14 15 16 ...
Страница 50: ...50 HELIX Spare parts diagram fluid section 1 2 3 4 7 8 15 16 17 18 19 20 21 22 23 9 10 11 12 13 14 5 6 ...