![background image](http://html1.mh-extra.com/html/titan/helix-0138011/helix-0138011_operating-manual_1119425004.webp)
4
SaFetY regulationS
HELIX
1
SAfeTy regulATIoNS
1.1
explANATIoN of SymBolS uSeD
This manual contains information that must be read and
understood before using the equipment. When you come to
an area that has one of the following symbols, pay particular
attention and make certain to heed the safeguard.
This symbol indicates a potential hazard
that may cause serious injury or loss of life.
Important safety information will follow.
Attention
This symbol indicates a potential hazard
to you or to the equipment. Important
information that tells how to prevent
damage to the equipment or how to avoid
causes of minor injuries will follow.
Danger of skin injection
Danger of fire from solvent and spray fumes
Danger of explosion from solvent, spray
fumes and incompatible materials
Danger of injury from inhalation of harmful
vapors
Danger of injury from burns
Danger of injury from electric shock
i
Notes give important information which
should be given special attention.
hAZArD: INjecTIoN INjury
Attention: Danger of injury by injection! A high
pressure stream produced by this equipment can
pierce the skin and underlying tissues, leading to
serious injury and possible amputation.
Do not treat a spraying injury as a harmless cut. In
case of injury to the skin through coating materials
or solvents, consult a doctor immediately for
quick and expert treatment. Inform the doctor
about the coating material or solvent used.
preveNTIoN:
•
NEVER aim the gun at any part of the body.
•
NEVER allow any part of the body to touch the fluid stream.
DO NOT allow body to touch a leak in the fluid hose.
•
NEVER put your hand in front of the gun.
•
ALWAYS lock the gun trigger, shut the fluid pump off
and release all pressure before servicing, cleaning the tip
guard, changing tips, or leaving unattended. Pressure
will not be released by turning off the engine. The PRIME/
SPRAY valve(s) or pressure bleed valve must be turned to
their appropriate positions to relieve system pressure.
•
All accessories must be rated at or above the maximum
operating pressure range of the sprayer. This includes
guns, extensions, and hose.
hAZArD: exploSIoN or fIre
Solvent and material fumes can explode or ignite.
Severe injury and/or property damage can occur.
preveNTIoN:
•
Only spray coating materials with a flash point of at least
5 kelvin higher than the set temperature (minimum flash
point is 38°C). The flash point is the lowest temperature
at which vapors develop from the coating material. These
vapors are sufficient to form an inflammable mixture over
the air above the coating material.
•
Do not use a material or solvent containing halogenated
hydrocarbons. Such as chlorine, bleach mildewcide,
methylene chloride and trichloroethane. They are not
compatible with aluminum. Contact the coating supplier
about compatibility of material with aluminum.
•
Do not use the unit in work places which are covered by
the explosion protection regulations.
•
Provide extensive exhaust and fresh air introduction to
keep the air within the spray area free from accumulation
of flammable vapors.
Содержание HELIX 0138011
Страница 12: ...12 SYSTEM DESCRIPTION HELIX A E D F L1 J H K K J N M M B H L2 G I C 3 3 System Diagram with circulation ...
Страница 44: ...44 HELIX Spare parts diagram drive assembly 4 5 6 1 2 3 7 8 9 10 11 18 17 12 13 14 15 16 ...
Страница 50: ...50 HELIX Spare parts diagram fluid section 1 2 3 4 7 8 15 16 17 18 19 20 21 22 23 9 10 11 12 13 14 5 6 ...