![background image](http://html1.mh-extra.com/html/titan/helix-0138011/helix-0138011_operating-manual_1119425006.webp)
6
SaFetY regulationS
HELIX
hAZArD: geNerAl
This product can cause severe injury or property
damage.
preveNTIoN:
•
Follow all appropriate local, state, and national codes
governing ventilation, fire prevention, and operation.
•
Pulling the trigger causes a recoil force to the hand that is
holding the spray gun. The recoil force of the spray gun is
particularly powerful when a high pressure has been set on
the airless pump. When cleaning, set the pressure control
to the lowest pressure.
•
Use only manufacturer authorized parts. User assumes all
risks and liabilities when using parts that do not meet the
minimum specifications and safety devices of the pump
manufacturer.
•
ALWAYS follow the material manufacturer’s instructions
for safe handling of chemicals.
•
Clean up all material and solvent spills immediately to
prevent slip hazard.
•
Never leave this equipment unattended. Keep away from
children or anyone not familiar with the operation of airless
equipment.
•
Device weighs in excess of 36 kg. Three-person lift is
required.
•
The device and all related liquids (i.e. hydraulic oil) must be
disposed of in an environmentally friendly way.
1.2
ISocyANATe (ISo) coNDITIoNS
Important Information Regarding Two-
Component Material. Read before using the
equipment.
ISocyANATe (ISo) coNDITIoNS
•
Use only Methyldiisocyanates (MDI).
•
Spraying materials that contain isocyanates (ISO) creates
mists, vapors and atomized particulates that are potentially
harmful.
•
Be familiar with the spray material’s SDS in order to
understand specific hazards and necessary precautions
that are related to the use of spray materials containing
isocyanates.
•
Provide extensive exhaust and fresh air introduction
to keep the air within the spray area free from harmful
isocyanate vapors. If sufficient ventilation is not available,
a supplied-air respirator must be available to everyone in
the work area.
•
AvoID ANy BAre-SKIN coNTAcT WITh ISocyANATeS.
To prevent contact with isocyanates, all persons located
within the spray area must be wearing the appropriate
protective equipment, including chemically impermeable
gloves, boots, aprons and goggles.
mATerIAl IgNITIoN
•
Some materials may become self-igniting if applied too
thickly. Read material manufacturer’s warnings and
material SDS.
Keep SprAy compoNeNTS SepArATe
•
Cross-contamination of individual spray materials can
result in cured material in fluid lines which can cause severe
injury and/or damage to the equipment.
•
To prevent cross-contamination of the equipment wetted
parts, Never interchange Component A (isocyanate) parts
with Component B (resin) parts.
moISTure SeNSITIvITy
Isocyanates (ISO) are catalysts used in two-component foam
and polyurea coatings. ISO will react with moisture (such as
humidity) to form small, hard abrasive crystals. These crystals
will then contaminate the fluid. Eventually a film will form
on the fluid surface and the ISO will begin to gel, increasing
in viscosity. Fluid contaminated with partially cured ISO , if
used, will reduce spray performance and the overall life of the
component wetted parts.
Содержание HELIX 0138011
Страница 12: ...12 SYSTEM DESCRIPTION HELIX A E D F L1 J H K K J N M M B H L2 G I C 3 3 System Diagram with circulation ...
Страница 44: ...44 HELIX Spare parts diagram drive assembly 4 5 6 1 2 3 7 8 9 10 11 18 17 12 13 14 15 16 ...
Страница 50: ...50 HELIX Spare parts diagram fluid section 1 2 3 4 7 8 15 16 17 18 19 20 21 22 23 9 10 11 12 13 14 5 6 ...