Thermo Scientific IonPac CG16 Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 67

background image

Product Manual for IonPac CS16

Page 52 of 65

6.1.2.

Replacing Column Bed Support Assemblies

If the column inlet bed support is determined to be the cause of the high back pressure, it should be replaced. If the bed
support is contaminated and/or deformed, it may be the cause of poor efficiency and/or poor peak shape. To change the inlet
bed support assembly, refer to the following instructions, using one of the two spare inlet bed support assemblies included in
the Ship Kit.

A.

Disconnect the column from the system.

B.

Carefully unscrew the inlet (top) column fitting.

Use two open-end wrenches.

C.

Remove the bed support.

Turn the end fitting over and tap it against a benchtop or other hard, flat surface to

remove the bed support and seal assembly. If the bed support must be pried out of the end fitting, use a sharp
pointed object such as a pair of tweezers, but be careful that you do not scratch the walls of the end fitting. Discard
the old bed support assembly.

D.

Place a new bed support assembly into the end fitting.

Make sure that the end of the column tube is clean and

free of any particulate matter so that it will properly seal against the bed support assembly. Use the end of the
column to carefully start the bed support assembly into the end fitting.

IonPac

CS16

IonPac

CS16

IonPac

CS16

5-mm

Columns

3-mm

Columns

0.5-mm

Columns

Part

(P/N)

(P/N)

(P/N)

Analytical

or

Capillary

Column

057573

059596

075401

Guard

Column

057574

059595

075402

Bed

Support

Assembly

042955

056823

N/A

End

Fitting

052809

052809

N/A

CAUTION

!

If the column tube end is not clean when inserted into the end fitting, particulate matter may obstruct a
proper seal between the end of the column tube and the bed support assembly. If this is the case, additional
tightening may not seal the column but instead damage the column tube or the end fitting.

E.

Screw the end fitting back onto the column.

Tighten it fingertight, then an additional 1/4 turn (25 in x lb). Tighten

further only if leaks are observed.

F.

Reconnect the column to the system and resume operation.

NOTE

!

Replace the outlet bed support ONLY if high pressure persists after replacement of the inlet fitting.

Document No. 031747-05

© 2010 Dionex Corporation

December 2010

«
...
52
53
54
55
56
...
»

Содержание IonPac CG16




































































Отзывы:

Нет отзывов

Похожие инструкции для IonPac CG16

Бренд: Oberheim Страницы: 40

Бренд: FJC Страницы: 2

Бренд: EASTERN INSTRUMENTS Страницы: 93

Бренд: EarthQuake Страницы: 12

Бренд: Pari Страницы: 2

Бренд: Gardena Страницы: 19

Бренд: Jackco Страницы: 6

Бренд: XanLite Страницы: 2

Бренд: X-Rite Страницы: 6

Бренд: Mako Страницы: 17

BOS R254K-UUI-LH10-S4

Бренд: Balluff Страницы: 12

Бренд: Ideal Heating Страницы: 16

Бренд: Parker Страницы: 24

Бренд: Sabo Страницы: 76

Бренд: Phenix Technologies Страницы: 39

Бренд: Triton Страницы: 31

Бренд: Kattsafe Страницы: 19

Бренд: Launch Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды