manualshive.com logo in svg

Thermo Scientific IonPac CG16, Руководство по эксплуатации продукта


Поделиться
Скачать
background image

Product Manual for IonPac CS16 

Page 63 of 65 

 

Document No. 031747-05 

© 2010 Dionex Corporation 

December 2010 

 

 

APPENDIX B - COLUMN CARE 

 

Recommended Operating Pressures 

 

Operating a column above its recommended pressure limit can cause irreversible loss of column performance. The maximum 
recommended operating pressure for the IonPac CS16 Analytical, Capillary or Guard Column is 4,000 psi (27.57 MPa). 
 

Do not use alcohols. 
Formation of esters will occur in the column packing. 
This can significantly reduce the column capacity for cation exchange. 
Do not use the CS16 column with basic eluents. 

 

Column Start-Up 

 

The column is shipped with eluent as the storage solution. This eluent is the same one shown in the test chromatogram. If you 
plan to use an eluent other than the test eluent, first equilibrate the column with the desired eluent for 30 to 60 minutes. The 
column is equilibrated when two consecutive injections of the standard produce the same retention times. 
 

Column Storage

 

The column’s storage solution should be the eluent used for the particular application. If the column will not be used for one 
week or more, prepare it for long term storage by flushing the column for a few minutes with the eluent. Cap both ends 
securely, using the plugs supplied with the column. 
 

Column Conditioning

 

For sample matrices that contain organic solvent content, it is recommended to condition the column with the following 
procedure: 
 

A.  Disconnet the column and direct the column effluent to a waste container. 
B.  Rinse the column for 90 minutes with 0.5 mN sulfuric acid and 10% acetonitrile. 
C.  Rinse the column for 30 minutes with eluent. 
D. Reconnect 

the 

column to the suppressor. 

 

Column Cleanup

 

The following column cleanup protocols have been divided into two general isocratic protocols:  
 

A. Acid 

soluble 

contaminants 

 
B.  Hydrophobic cations and organic contaminants. 
 

Always ensure that the cleanup protocol used does not switch between eluents which may create high pressure 
eluent interface zones in the column. High pressure zones can disrupt the uniformity of the packing of the column 
bed and irreversibly damage the performance of the column. High pressure zones in the column can be created by 
pumping successive eluents through the column that are not miscible, that have eluent components in one eluent that 
will precipitate out in the other eluent or by using an acid eluent followed by a base eluent with may create a 
neutralization pressure band. The precipitation of the salts in solvents during column rinses can result in very high 
pressure zones. High viscosity mixing zones can be created between two eluents having solvents with a very high 
energy of mixing. 

 

When in doubt, always include short column steps to reduce the solvent content of the eluent to < 5% levels and the 
ionic strength of the eluent to < 50 mM levels to avoid creating high pressure zones in the column that may disrupt 
the uniformity of the column packing. This intermediate low concentration step will prevent precipitation or high 
viscosity zones. Avoid creating high pressure zones in the column that may disrupt the uniformity of the column 
packing. 

 
 

CAUTION

!

Содержание IonPac CG16




































































Отзывы:

Нет отзывов

Похожие инструкции для IonPac CG16

Pall T Series Care And Use preview
T Series
Бренд: Pall Страницы: 51
ZAMST A1 Instructions For Use Manual preview
A1
Бренд: ZAMST Страницы: 21
Laica SB2200 Instructions And Guarantee preview
SB2200
Бренд: Laica Страницы: 4
Eclipse Combustion 6500 Instruction Manual preview
6500
Бренд: Eclipse Combustion Страницы: 46
Bard Duet Instructions For Use preview
Duet
Бренд: Bard Страницы: 2
Vahle VCL Series Translation Of The Original Operating Instructions preview
VCL Series
Бренд: Vahle Страницы: 96
Garmin GSD20 Sounder Installation Manual preview
GSD20 Sounder
Бренд: Garmin Страницы: 12
Garmin GC 12 Installation Instructions Manual preview
GC 12
Бренд: Garmin Страницы: 13
VelociRAX Light Bar Instruction Manual preview
Light Bar
Бренд: VelociRAX Страницы: 4
ABM Katana User Manual preview
Katana
Бренд: ABM Страницы: 17
Haemonetics Cell Saver Elite+ User Manual preview
Cell Saver Elite+
Бренд: Haemonetics Страницы: 230
Xylem McDonnell & Miller PSE-800-M Application, Installation, Operation, And Maintenance Manual preview
McDonnell & Miller PSE-800-M
Бренд: Xylem Страницы: 20
Össur QUICK-ALIGN Vari-Flex Instructions For Use Manual preview
QUICK-ALIGN Vari-Flex
Бренд: Össur Страницы: 36
Össur Patriot Collar Instructions For Use preview
Patriot Collar
Бренд: Össur Страницы: 2
Össur Unloader One Instructions For Use Manual preview
Unloader One
Бренд: Össur Страницы: 8
Pentair Maestro SB-CO-DIV-008B Installation And User Manual preview
Maestro SB-CO-DIV-008B
Бренд: Pentair Страницы: 52
R.V.R. Elettronica TOUCH30S User Manual preview
TOUCH30S
Бренд: R.V.R. Elettronica Страницы: 38
Studio Technologies 45DR User Manual preview
45DR
Бренд: Studio Technologies Страницы: 23

Бренды по названию

Популярные бренды

Загрузить еще бренды