Thermo Scientific Barnstead EASYpure RODI 1332 Series Скачать руководство пользователя страница 49

Страница: 49 / 60

4. Carefully and cleanly cut the EASYpure R

feed-

water tubing such that one piece will connect the

EASYpure R

to the external accessory pump.

The other piece will be used to connect the facility

water supply to the “inlet” of the accessory pump.

Use 90-degree fittings as necessary to help route

tubing to and from the external pump accessory.

5. Attach power cable from back of EASYpure R

into the side of the Pump Housing.

6. Open facility water supply valve and check

AY1332X1 for leaks.

7. Turn power on to the EASYpure R

system and

operate normally.

AY1332X2 External Filter

Accessory

This accessory should be used when customer site has feed-

water with high particulate and/or high scaling contaminants.

If in doubt contact Technical Service for possible feedwater

testing.

Accessory Kit Includes:

1. Filter housing (1)

2. Plumbing adapters (2)

3. Pressure gauges (2)

4. Filter/Antiscalant assembly (1)

5. Wall bracket (1)

6. Screw/washer sets for bracket/housing connection (4)

Installation Instructions

1. Turn power off to the EASYpure R

system.

2. Close facility water supply valve.

CCESSORIES

Содержание Barnstead EASYpure RODI 1332 Series





























































Результаты поиска

Содержание Barnstead EASYpure RODI 1332 Series

Отзывы:

Похожие инструкции для Barnstead EASYpure RODI 1332 Series

Бренды по названию

Популярные бренды

Thermo Scientific Barnstead EASYpure RODI 1332 Series, Инструкция по эксплуатации и список запасных частей

Результаты поиска

Содержание Barnstead EASYpure RODI 1332 Series

Отзывы:

Похожие инструкции для Barnstead EASYpure RODI 1332 Series

Бренды по названию

Популярные бренды