Thermo Scientific Barnstead EASYpure RODI 1332 Series Скачать руководство пользователя страница 28

Страница: 28 / 60

System Cleaning

Frequency of cleaning will vary, depending on quality of

feedwater and usage. Cleaning is necessary in any of the

following occur: If residual deposits are evident inside

feedwater reservoir, or if a new 0.2 micron final filter clogs

rapidly. To clean the EASYpure R

the following is nec-

essary: a) two empty cartridges (ordered separately, part

number D7034), b) hose barb used during initial installa-

tion.

1. Remove cartridges from positions 2 and 3 and

discard. Install empty cartridges (part number

D7034) according to the instructions in

Cartridge Replacement

. Remove and

replace cartridges one at a time to avoid drain-

ing UV chamber.

2. Remove 0.2 micron final filter and install the

hose barb that was shipped with the system.

3. Remove Ventgard cap (be sure the reservoir

tank is full) and add 10ml to 20ml of household

chlorine bleach (5.25% sodium hypochlorite) to

reservoir.

4. Replace Ventgard cap. Press the

“START/STOP” button to put unit into Run

Mode.

5. Allow the unit to recirculate the cleaning solu-

tion for thirty minutes.

6. Drain the system.

a. Put the unit into Run Mode and place a bucket

or other suitable large container under the valve

and draw off water as described under

Water

Draw-Off

in the

Operation

section of this man-

ual. To clean the valve. Draw off water until the

water level in the feedwater reservoir is lowered

to the point that “Add” is displayed. Lift draw-off

valve to closed position.

b. Put the unit in Idle Mode, shut power off and

disconnect the power cord from the power entry

module. Disconnect water supply.

Maintenance and Servicing

Warning

Disconnect from the power supply prior

to maintenance and servicing.

Do not disassemble water lines or re-

move cartridges where spilled water

could contact equipment that requires

electrical service. Electrical shock

hazard could result.

Refer servicing to qualified personnel.

Note

Empty cartridges must be ordered

separately. Contact customer serv-

ice and order part number D7034.

Warning

Avoid splashing cleaning solutions on

clothing or skin.

Ensure all piping connections are tight

to avoid chemical leakage.

Ensure adequate ventilation when

using chemicals for cleaning.

Carefully follow manufacturerʼs safety

instructions on labels of chemical

containers and Material Safety Data

Sheets (M.S.D.S).

Содержание Barnstead EASYpure RODI 1332 Series





























































Результаты поиска

Содержание Barnstead EASYpure RODI 1332 Series

Отзывы:

Бренды по названию

Популярные бренды

Thermo Scientific Barnstead EASYpure RODI 1332 Series, Инструкция по эксплуатации и список запасных частей

Результаты поиска

Содержание Barnstead EASYpure RODI 1332 Series

Отзывы:

Бренды по названию

Популярные бренды