Thermo Scientific Barnstead EASYpure RODI 1332 Series Скачать руководство пользователя страница 43

Страница: 43 / 60

ROUBLESHOOTING

Problem (cont.)

Possible Causes (cont.)

Action (cont.)

Tank not filling (low pressure indicated by

Feedwater supply valve closed.

Open feedwater supply valve.

gauge.)

RO prefilter plugged.

Replace RO prefilter.

Solenoid valve not open.

Call Technical Service.

Feed pressure below specification.

Increase pressure.

Low RO purity LED illuminated.

New RO membrane rinsing up.

Continue rinse-up.

Improperly installed RO membrane.

Be sure RO membrane is installed

properly.

Decrease in % rejection.

Fouled RO membrane.

Replace RO membrane.

Decrease in system productivity.

Decrease in water temperature.

If decline in flowrate is unacceptable,

install feedwater temperature valve

to elevate water temperature. Valve

available by calling customer service.

RO membrane fouled.

Replace RO membrane.

Low incoming water pressure.

Be sure prefilter is not blocked.

Increase incoming water pressure.

Low RO membrane operating

Increase operating pressure. If

pressure.

needed, use Barnstead accessory

AY1332X1 external pressure boost

assembly.

RO prefilter plugs rapidly.

High turbidity feedwater.

Call Technical Service. If needed, use

Barnstead accessory AY1332X2

External Filter Assembly with gauges.

This contains high volume 5 micron

particulate filtering in conjunction

with membrane antiscalant.

Содержание Barnstead EASYpure RODI 1332 Series





























































Результаты поиска

Содержание Barnstead EASYpure RODI 1332 Series

Отзывы:

Похожие инструкции для Barnstead EASYpure RODI 1332 Series

Бренды по названию

Популярные бренды

Thermo Scientific Barnstead EASYpure RODI 1332 Series, Инструкция по эксплуатации и список запасных частей

Результаты поиска

Содержание Barnstead EASYpure RODI 1332 Series

Отзывы:

Похожие инструкции для Barnstead EASYpure RODI 1332 Series

Бренды по названию

Популярные бренды