Thermo Scientific Barnstead EASYpure RODI 1332 Series Скачать руководство пользователя страница 50

Страница: 50 / 60

3. Completely and securely assemble AY1332X2 com-

ponents. See drawing on page 53. (Note orientation

of Filter/Antiscalant assembly). The use of

PTFE

tape on NPT treads is recommended to aid in a

secure leak proof assembly.

4. Using 2 customer-supplied fasteners, install the

assembly on a wall in a location convenient for filter

exchange. Be sure NOT to mount the assembly

over anything that could be damaged or be a safety

issue if water spillage occurs.

5. Install the D13321 inlet tubing connection into the

outlet plumbing adapter.

6. Using a customer-supplied tubing/fitting (1/4 inch

male NPT), securely attach feedwater connection to

the 1/4 inch female NPT inlet plumbing adapter.

7. Open facility water supply valve and check

AY1332X2 assembly for leaks.

8. Turn power on to EASYpure R

system and oper-

ate normally.

Filter/Antiscalant Cartridge Exchange

Filter/Antiscalant cartridge should be exchanged whenever

inlet-outlet pressure difference exceeds 10psi (0.69 bar).

1. Turn power off to the EASYpure R

system.

2. Close/shut off facility water supply or supply valve

(located upstream of the AY1332X2 assembly.)

3. Depressurize housing by momentarily pressing the

RED button on top of the housing cover. Note that a

very small amount of water may spray out of the

depressurization valve, under the RED button, dur-

ing this step.

4. Carefully unscrew housing from housing cover, as it

will be filled with water.

5. Remove and discard old Filter/Antiscalant cartridge.

CCESSORIES

Содержание Barnstead EASYpure RODI 1332 Series





























































Результаты поиска

Содержание Barnstead EASYpure RODI 1332 Series

Отзывы:

Похожие инструкции для Barnstead EASYpure RODI 1332 Series

Бренды по названию

Популярные бренды

Thermo Scientific Barnstead EASYpure RODI 1332 Series, Инструкция по эксплуатации и список запасных частей

Результаты поиска

Содержание Barnstead EASYpure RODI 1332 Series

Отзывы:

Похожие инструкции для Barnstead EASYpure RODI 1332 Series

Бренды по названию

Популярные бренды