Thermo Scientific Barnstead EASYpure RODI 1332 Series Скачать руководство пользователя страница 35

Страница: 35 / 60

10. Close the cartridge access door.

11. Install the hose barb into the fitting in the draw-

off valve.

12. Turn unit on and from “IdL” press the

START/STOP button to begin unit operation.

13. Rinse approximately 3 liters (1/2 reservoir vol-

ume) of water through the draw-off valve to

drain.

14. Close the draw-off valve.

15. Remove the hose barb from the draw-off valve

and proceed to the

0.2 Micron Final Filter

Replacement

section of this manual.

16. Place unit in Run Mode until desired purity is

achieved.

UV Lamp Replacement (See Fig. 5)

Lamp life will vary according to the number of times the

EASYpure R

unit is turned on and off. The UV lamp

should be replaced a minimum of every 12 months of

operation. If the EASYpure R

is cycled between Run,

Standby and Idle Modes frequently during the work day,

this may result in a shorter lamp life. Therefore, it is rec-

ommended that the EASYpure R

be left in the Run

Mode during normal working hours and in Standby Mode

at night and on weekends.

To replace the ultraviolet lamp:

1. Turn off the EASYpure R

and disconnect it

from the power supply. Remove the power

cord.

2. Depressurize the system by opening draw-off

valve and allowing water to drain from the unit.

Disconnect water line.

3. Remove the reservoir Ventgard cap.

AINTENANCE AND

ERVICING

Warning

This unit is equipped with an ultraviolet

lamp. Ultraviolet radiation is harmful to

the eyes and skin. Do not attempt to

observe the lamp directly, while it is

illuminated.

Caution

Do not unscrew the metal end cap

cover of the UV chamber, as this will

loosen the water tight seal and may

damage the replacement lamp. Pull the

black plastic cover straight up.

Warning

Depressurize system prior to removing

cover.

Содержание Barnstead EASYpure RODI 1332 Series





























































Результаты поиска

Содержание Barnstead EASYpure RODI 1332 Series

Отзывы:

Похожие инструкции для Barnstead EASYpure RODI 1332 Series

Бренды по названию

Популярные бренды

Thermo Scientific Barnstead EASYpure RODI 1332 Series, Инструкция по эксплуатации и список запасных частей

Результаты поиска

Содержание Barnstead EASYpure RODI 1332 Series

Отзывы:

Похожие инструкции для Barnstead EASYpure RODI 1332 Series

Бренды по названию

Популярные бренды