Thermo Scientific Barnstead EASYpure RODI 1332 Series Скачать руководство пользователя страница 21

Страница: 21 / 60

FLUSH

: Manual Flush: Pressing the Flush

switch once will initiate a one minute flush of the

RO membrane and the display will show FL1.

Pressing the Flush switch twice will initiate a five

minute flush of the RO membrane. During this

five minute flush, the display will count down

FL5, FL4, FL3, etc. After the timed flush has

ended, the EASYpure R

will return to the

mode (“IdL”, Run or “SbY”) it was in when you

initiated the flush.

AUTOMATIC FLUSH

: In the Run and Standby

Mode, the EASYpure R

will initiate a one

minute automatic flush of the RO membrane

once every twenty-four hours (purity value being

displayed.)

Display (See Fig. 12)

In addition to displaying the temperature compensated

(25°C) resistivity in megohms-cm, the display also indi-

cates operational modes and error indicators. The follow-

ing is what can appear on the display:

SbY

Er1

rEC

Er3

IdL

Er4

AFL

Er5

FL5

Er6

FL4

Er7

FL3

Add

FL2

FL1

Three LEDs illuminate to provide system operational sta-

tus as follows:

•

RO System Operating:

Green LED ON - RO

Operation is ON; LED OFF - RO Flush or RO

Operation is OFF.

•

Low RO Purity:

Red LED ON - % rejection

between incoming water and product water is

lower than expected; LED OFF - % reject is

good.

•

Replace RO Prefilter:

Red LED ON - Unit has

been in service for 6 months, replace RO pre-

filter; LED OFF - replace prefilter as needed and

reset timer.

ONTROLS AND

ORMAL

PERATION

Note

When the RO operation is automati-

cally turned on, only RO water that

is above the specified % rejection

setting (factory set to 75%) will be

put into the tank. Anytime the RO

purity falls below the % rejection set-

ting the water will be diverted away

from the tank and sent to drain.

Содержание Barnstead EASYpure RODI 1332 Series





























































Результаты поиска

Содержание Barnstead EASYpure RODI 1332 Series

Отзывы:

Бренды по названию

Популярные бренды

Thermo Scientific Barnstead EASYpure RODI 1332 Series, Инструкция по эксплуатации и список запасных частей

Результаты поиска

Содержание Barnstead EASYpure RODI 1332 Series

Отзывы:

Бренды по названию

Популярные бренды