Thermo Scientific Barnstead EASYpure RODI 1332 Series Скачать руководство пользователя страница 26

Страница: 26 / 60

7. Again apply power to the system and press the

ʻStart/Stopʼ switch to start operation. Let the

reservoir fill completely (may take up to six

hours). During the filling process the unit

pump may turn on/off and the unit display may

alternate between “Add” and displaying a purity

value, as the cartridges are slowly wetted.

Reservoir will be completely full when the ʻRO

System Operatingʼ LED is no longer illuminat-

ed.

8. Place the unit into “IdL” by pressing the

START/STOP switch.

9. Install the hose barb fitting (included with

accessories) into the draw-off valve assembly

and place a suitable container under the draw-

off valve.

10. Press the START/STOP switch and open the

draw-off valve.

11. Rinse 1/2 of the total reservoir volume through

the cartridges into the container, close the

draw-off valve and discard the water.

12. Remove the hose barb fitting from the draw-off

valve. Keep the hose barb fitting for future

use.

13. Remove the new 0.2-micron final filter assem-

bly from its bag and insert it into the draw-off

valve. Gently tighten, turning the filter to the

right. Remove the protective cap from filter.

14. Open the draw-off valve and flush the remain-

ing 1/2 reservoir volume of water through the

0.2-micron final filter. “Add” will be displayed

when the tank is empty.

15. Close the draw-off valve and replace protective

cap on filter.

16. Allow the reservoir to refill itself and the system

to go into recirculation.

NITIAL

PERATION

Note

It is suggested that

PTFE

tape be

applied to the threads of the 0.2 micron

final filter to ensure a tight seal.

Содержание Barnstead EASYpure RODI 1332 Series





























































Результаты поиска

Содержание Barnstead EASYpure RODI 1332 Series

Отзывы:

Бренды по названию

Популярные бренды

Thermo Scientific Barnstead EASYpure RODI 1332 Series, Инструкция по эксплуатации и список запасных частей

Результаты поиска

Содержание Barnstead EASYpure RODI 1332 Series

Отзывы:

Бренды по названию

Популярные бренды