Thermo Scientific Barnstead EASYpure RODI 1332 Series Скачать руководство пользователя страница 44

Страница: 44 / 60

ROUBLESHOOTING

Error Conditions

Problem

Possible Causes

Action

Display reads “Er1”

Air in system.

Purge air from system by

(Purity measurement error)

drawing off water according to

the instructions in the Operation

section.

Resistivity cell not connected to

Check resistivity cell lead

PCX70 meter board connection (P1).

connections (P1) on circuit board.

(See Wiring Diagram)

Resistivity cell dirty.

Clean cell and reinstall.

Resistivity cell out of tolerance.

Replace resistivity cell.

Display reads “Er3”.

UV lamp cable not plugged into J6 of

Plug UV lamp cable into J6 of

(UV lamp error)

PC1302X1.

PC1302X1 daughter board.

(See Wiring Diagram)

UV lamp burnt out or nearing the end

Replace UV lamp (LMX13).

of its useful life.

Chamber seal is compromised and

Replace quartz sleeve and o-rings.

UV lamp is getting wet.

Call Technical Service.

UV lamp not properly connected to

Recheck/reconnect.

UV cable connector.

UV ballast out of tolerance.

Replace ballast. Call Technical

Service.

Display reads “Er4”

Resistivity cell not connected to

Check resistivity cell lead

(Cell temperature sensor error)

meter board (PCX70).

connection (P1) on meter board.

(PCX70) (See Wiring Diagram)

Resistivity cell dirty.

Clean cell and reinstall.

Resistivity cell temperature

Replace resistivity cell (E703X1A).

sensor out of tolerance.

Meter board out of tolerance.

Replace meter board (PCX70).

Call Technical Service.

Display reads “Er5”.

PC board communication trouble.

Cycle power.

(Meter board data error)

Meter board not connected

Check connection from meter

to display/control board.

board (PCX70 10 pin connector)

to display/control board (J2).

Meter board (PCX70) out of

Replace meter board (PCX70).

tolerance.

Call Technical Service.

Содержание Barnstead EASYpure RODI 1332 Series





























































Результаты поиска

Содержание Barnstead EASYpure RODI 1332 Series

Отзывы:

Похожие инструкции для Barnstead EASYpure RODI 1332 Series

Бренды по названию

Популярные бренды

Thermo Scientific Barnstead EASYpure RODI 1332 Series, Инструкция по эксплуатации и список запасных частей

Результаты поиска

Содержание Barnstead EASYpure RODI 1332 Series

Отзывы:

Похожие инструкции для Barnstead EASYpure RODI 1332 Series

Бренды по названию

Популярные бренды