Thermo Scientific Barnstead EASYpure RODI 1332 Series Скачать руководство пользователя страница 25

Страница: 25 / 60

Storage Reservoir Filling and

Cartridge/Membrane Rinse Up

RO Membrane Rinse-Up:

1. During initial operation be sure the reservoir

Drain Plug (bottom rear of unit) is removed and

that the unit is placed such that the reservoir

drain is over a sink to allow for proper rinsing

of RO membrane.

2. Connect water supply to unit by inserting the

quick disconnect into the feed water inlet on

the lower left side in the rear of the EASYpure

. Turn on main water supply. Turn the

system power on by depressing the Main

Power Switch to the ʻIʼ position. A power-up

sequence will occur showing the unit type,

lighting up all the LEDs, showing the software

revision and finally displaying “IdL”.

3. Reset the carbon prefilter timer. (See “To Reset

Carbon Prefilter Timer.”)

4. Press the ʻStart/Stopʼ switch on the keypad to

start operation. Display will show “Add” and

the ʻRO System Operatingʼ LED will be illumi-

nated. The DI pump and UV lamp will not turn

on any time “Add” is displayed.

5. 2 Hour New Membrane Rinse-

Allow the unit to operate until the display

shows “Er7” (approximately 2 hours.) This will

rinse the new membrane of its preservatives. It

is possible that during this time the “Low RO

Purity” LED may illuminate.

6. After the membrane rinse the unit can be shut

down and the reservoir drain plug can be re-

inserted (insert completely then back out very

slightly).

Initial Operation

Note

Cartridge rinse up procedure must be

followed after each cartridge and/or fil-

ter replacement.

Note

For more demanding applications

where low TOC water is required, a

third reservoir volume rinse of the car-

tridges and filter may be necessary.

Warning

Use a properly grounded

electrical outlet of correct voltage

and current handling capacity.

Warning

This device is to be used with

potable water feeds only. Cleaning

agents must be used in compliance

with instructions in this manual.

Failure to comply with the above

could result in explosion and person-

al injury.

Note

The display will read “ADD” when

the reservoir is filling and water is

not running through DI cartridge.

Содержание Barnstead EASYpure RODI 1332 Series





























































Результаты поиска

Содержание Barnstead EASYpure RODI 1332 Series

Отзывы:

Похожие инструкции для Barnstead EASYpure RODI 1332 Series

Бренды по названию

Популярные бренды

Thermo Scientific Barnstead EASYpure RODI 1332 Series, Инструкция по эксплуатации и список запасных частей

Результаты поиска

Содержание Barnstead EASYpure RODI 1332 Series

Отзывы:

Похожие инструкции для Barnstead EASYpure RODI 1332 Series

Бренды по названию

Популярные бренды