Thermo Scientific AI 3000 Скачать руководство пользователя страница 52

Страница: 52 / 108

Installation

Installing the Sampling System Support on the TRACE 1300/TRACE 1310

AI 3000/AS 3000 Sampling System - Operating Manual

Thermo Scientific

Assembling of the Sampling System Support on the Back Injector Module

The following is the description of how to mount the sampling system support on the

back

injector module of the TRACE 1300/TRACE 1310. See

Figure 31

and

Figure 32

Figure 31.

Assembling on the Back Injector Module (1)

1. Remove from the GC top cover the three plastic caps covering the corresponding fixing

holes. See A, B, and C.

2. Orient the L-shape bottom plate to align the three installation holes to the corresponding

fixing holes located on the GC top.

3. Insert the provided fixing screws into the holes present on the L-shape bottom plate.

Note

In comparison with the installation on the front injector module, the

installation on the back injector module requires to upturn the L-shape bottom plate
before fixing it on the GC.

L-shape Bottom Plate

Содержание AI 3000













































































































Результаты поиска

Содержание AI 3000

Отзывы:

Похожие инструкции для AI 3000

Бренды по названию

Популярные бренды

Thermo Scientific AI 3000, Руководство по эксплуатации

Результаты поиска

Содержание AI 3000

Отзывы:

Похожие инструкции для AI 3000

Бренды по названию

Популярные бренды