Thermo Scientific AI 3000 Скачать руководство пользователя страница 62

Страница: 62 / 108

Installation

Installing the Sampling System Support on the TRACE GC Ultra

AI 3000/AS 3000 Sampling System - Operating Manual

Thermo Scientific

1. Remove the cover and the collar of the injector and detector compartment.

2. Open the column oven door. Loosen the two knobs located in the upper parts.

3. Push the cover backwards and remove it.

4. Screw the spacer on the threaded pin.

5. Put the GC cover back in the original position.

6. Tighten the two knobs. Close the column oven door.

7. Mount the spacer fixing Allen screw.

8. Reinstall the cover and the collar of the injector and detector compartment.

Assemble the sampling system support on the GC according to the required configuration.

Assembling of the Sampling System Support on the GC Right Side

The following is the description of how to mount the sampling system support in the default
configuration, i.e. on the

right

side of the TRACE GC Ultra.

1. Remove from the GC top cover the two plastic caps covering the corresponding fixing

holes.

2. Insert into each slot present on the support the provided fixing screw.

3. Insert each screw into the relevant spacer paying attention to keep its largest surface

turned towards the support base.

4. Holding the spacers in position with your hands, rest the support on the GC top cover,

with their flat side towards the inside.

5. Guide the two fixing screws located on the external spacers into the corresponding fixing

holes.

6. Loosely tighten the screws.

Assembling of the Sampling System Support on the GC Left Side

The following is the description of how to mount the sampling system support on the

left

side

of the TRACE GC Ultra.

1. Remove from the GC top cover the four plastic caps covering the corresponding fixing

holes.

2. Mount the support bracket on the TRACE GC Ultra and fix by using fixing screws

provided.

3. Insert into each slot present on the support the provided fixing screw.

Содержание AI 3000













































































































Результаты поиска

Содержание AI 3000

Отзывы:

Похожие инструкции для AI 3000

Бренды по названию

Популярные бренды

Thermo Scientific AI 3000, Руководство по эксплуатации

Результаты поиска

Содержание AI 3000

Отзывы:

Похожие инструкции для AI 3000

Бренды по названию

Популярные бренды