Thermo Scientific 42iQTL Скачать руководство пользователя страница 83

Страница: 83 / 310

Operation

Settings

Thermo Scientific

42iQTL Instruction Manual

3-57

●

Converter Valve:

Displays whether or not the converter valve is

activated.

●

Prereactor Valve:

Displays whether or not the prereactor valve is

activated.

●

Instrument Error:

Displays OK/Fail for PCP, datalogging,

streaming, serial server, and Modbus protocols.

●

Board Communication:

Displays OK/Fail for board communication

status.

●

Power Supply:

Displays OK/Fail of power supplies. Power supply

goes red if any voltages are outside their limits. No voltage rows
ever get highlighted.

●

2.5V Diagnostic:

Displays current voltage readings. Alarm limits

are not changeable.

●

3.3V Diagnostic:

Displays current voltage readings. Alarm limits

are not changeable.

●

5.0V Diagnostic:

Displays current voltage readings. Alarm limits

are not changeable.

●

24V Diagnostic:

Displays current voltage readings. Alarm limits

are not changeable.

●

5.0V Step Board 1:

Displays OK/Fail.

●

24V Step Board 1:

Displays OK/Fail.

●

5.0V Step Board 2:

Displays OK/Fail.

●

24V Step Board 2:

Displays OK/Fail.

Содержание 42iQTL























































































































































































































































































































Результаты поиска

Содержание 42iQTL

Отзывы:

Бренды по названию

Популярные бренды

Thermo Scientific 42iQTL, Инструкция по эксплуатации

Результаты поиска

Содержание 42iQTL

Отзывы:

Бренды по названию

Популярные бренды