Thermo Scientific 42iQTL Скачать руководство пользователя страница 285 | Manualshive

Страница: 285 / 310

Thermo Scientific 42iQTL Скачать руководство пользователя страница 285

Thermo Scientific

42iQTL Instruction Manual

A-1

Appendix A

Safety, Warranty, and WEEE

Review the following information carefully before using the instrument.
This manual provides specific information on how to operate the
instrument, however if the instrument is used in a manner not specified by
the manufacturer, the protection provided by the equipment may be
impaired.

This manual contains important information to alert you to potential safety
hazards and risks of equipment damage. Refer to the following types of
alerts you may see in this manual.

Safety and Equipment Damage Alert Descriptions

Alert



Description



A hazard is present that will result in death or serious
personal injury if the warning is ignored.

▲



A hazard is present or an unsafe practice can result in
serious personal injury if the warning is ignored.

▲



The hazard or unsafe practice could result in minor to
moderate personal injury if the warning is ignored.

▲

Equipment Damage

The hazard or unsafe practice could result in property
damage if the warning is ignored.

▲

Safety and Equipment Damage Alerts in this Manual

Alert



Description



If the equipment is operated in a manner not specified by
the manufacturer, the protection provided by the equipment
may be impaired.

▲



The service procedures in this manual are restricted to
qualified service personnel only.

▲

Equipment Damage

Do not attempt to lift the analyzer by the cover or other
external fittings.

▲

This adjustment should only be performed by an instrument
service technician.

▲

Safety

Safety and

Equipment Damage

Alerts

«
...
283
284
285
286
287
...
»

Содержание 42iQTL























































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды