Thermo Scientific 42iQTL Скачать руководство пользователя страница 111

Страница: 111 / 310

Operation

Settings

Thermo Scientific

42iQTL Instruction Manual

3-85

●

Down:

●

Manual Entry:

Shows current value. If the input board cal cell is

pressed, user can manually change the value.

●

Auto Cal:

When pressed, the auto-calibration process is initiated.

Please allow up to 5 minutes for calibration to complete.

●

End Cal:

When pressed, the auto calibration is interrupted and the

value does not change.

●

PMT Voltage:

Displays PMT voltage.

●

Frequency:

Displays frequency.

●

Zero Offset Freq:

Displays zero offsets frequency.

●

Default Values:

When pressed, the default values are saved.

Home Screen>Settings>Measurement Settings>Advanced Measurement
Settings>Reaction Chamber Settings>Continue to PMT Calibration
Screen

The PMT Calibration screen contains the following information:

●

Across:

●

Description:

Defines the actions the user can do.

●

PMT Supply:

User can manually adjust the PMT supply value,

adjust target concentration and read calibration concentration,
start/stop automatic calibration, read voltage, frequency and zero
offset frequency values, and reset default values.

●

Current PMT:

Displays the current PMT voltage value.

●

Units:

Displays units for each item.

Содержание 42iQTL























































































































































































































































































































Результаты поиска

Содержание 42iQTL

Отзывы:

Бренды по названию

Популярные бренды

Thermo Scientific 42iQTL, Инструкция по эксплуатации

Результаты поиска

Содержание 42iQTL

Отзывы:

Бренды по названию

Популярные бренды