Thermo Scientific 42iQTL Скачать руководство пользователя страница 45

Страница: 45 / 310

Operation

Calibration

Thermo Scientific

42iQTL Instruction Manual

3-19

The Zero/Span Schedule is used to program the instrument to perform
fully automated zero and span checks or adjustments.

Home Screen>Calibration>Zero/Span Schedule

Home Screen>Calibration>Zero/Span Schedule>More

The Zero/Span Schedule contains the following information:

●

Zero/Span Schedule:

Toggles zero/span schedule Enabled or Disabled.

●

Next Time:

Allows the user to view and set the initial date and time

(24-hour format) of the zero/span schedule.

●

Period:

Defines the period or interval between zero/span checks or

calibrations. If period = 0, the schedule runs continuously.

●

Zero Duration:

Sets how long zero air is sampled by the instrument.

●

Span Duration:

Sets how long span gas is sampled by the instrument.

●

Purge Duration:

Sets how long the purge period will be at the end of

the schedule.

●

Total Duration:

Read only. Displays the total time duration of all

scheduled events.

Zero/Span Schedule

Содержание 42iQTL























































































































































































































































































































Результаты поиска

Содержание 42iQTL

Отзывы:

Бренды по названию

Популярные бренды

Thermo Scientific 42iQTL, Инструкция по эксплуатации

Результаты поиска

Содержание 42iQTL

Отзывы:

Бренды по названию

Популярные бренды